Modeling and simulation of heat transfer, fluid flow and geometry morphology in GMAW-based wire arc additive manufacturing

Influence of interpass cooling conditions on microstructure and tensile properties of Ti-6Al-4V parts manufactured by WAAM

(2020) L. Vázquez et al.   Welding in the World

Determination of the control points for circle and triangle route in wire arc additive manufacturing (WAAM)

(2020) W. Ou et al.   Journal of Manufacturing Processes

Control of deposition height in WAAM using visual inspection of previous and current layers

(2020) Jun Xiong et al.   JOURNAL OF INTELLIGENT MANUFACTURING

Increasing the manufacturing efficiency of WAAM by advanced cooling strategies

(2020) Uwe Reisgen et al.   Welding in the World

Wire Arc Additive Manufacturing (WAAM) of Aluminum Alloy AlMg5Mn with Energy-Reduced Gas Metal Arc Welding (GMAW)

(2020) Maximilian Gierth et al.   Materials

Effects of Thermal Cycling on Wire and Arc Additive Manufacturing of Al-5356 Components

(2020) Markus Köhler et al.   Metals

Current Status and Perspectives on Wire and Arc Additive Manufacturing (WAAM)

(2019) Tiago A. Rodrigues et al.   Materials

Effect of heat input on microstructure and mechanical properties of Al-Mg alloys fabricated by WAAM

(2019) Chuanchu Su et al.   APPLIED SURFACE SCIENCE

Heat transfer, fluid flow and electromagnetic model of droplets generation and melt pool behaviour for wire arc additive manufacturing

(2019) S. Cadiou et al.   INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER

Molten pool behaviors and their influences on welding defects in narrow gap GMAW of 5083 Al-alloy

(2018) Chenxiao Zhu et al.   INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER

Numerical analysis of heat transfer and fluid flow in multilayer deposition of PAW-based wire and arc additive manufacturing

(2018) Xingwang Bai et al.   INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER

Study of mass transport in cold wire deposition for Wire Arc Additive Manufacturing

(2018) Fatemeh Hejripour et al.   INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER

Optimising the mechanical properties of Ti-6Al-4V components produced by wire + arc additive manufacturing with post-process heat treatments

(2018) M.J. Bermingham et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Rapid prototyping of 4043 Al-alloy parts by cold metal transfer

(2018) Yunpeng Nie et al.   SCIENCE AND TECHNOLOGY OF WELDING AND JOINING

Numerical simulation of WAAM process by a GMAW weld pool model

(2018) Y. Ogino et al.   Welding in the World

Fusion zone geometries, cooling rates and solidification parameters during wire arc additive manufacturing

(2018) W. Ou et al.   INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER

Numerical analysis of thermal fluid transport behavior during electron beam welding of 2219 aluminum alloy plate

(2017) Cheng-cai LIU et al.   TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA

Three-dimensional numerical simulation of arc and metal transport in arc welding based additive manufacturing

(2016) Xiangman Zhou et al.   INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER

Wire + Arc Additive Manufacturing

(2016) S. W. Williams et al.   MATERIALS SCIENCE AND TECHNOLOGY

The status, challenges, and future of additive manufacturing in engineering

(2015) Wei Gao et al.   COMPUTER-AIDED DESIGN

On the influence of initial geometry on the evolution of fluid filaments

(2015) K. Mahady et al.   PHYSICS OF FLUIDS

Effect of arc mode in cold metal transfer process on porosity of additively manufactured Al-6.3%Cu alloy

(2014) Baoqiang Cong et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Simulation of metal transfer in GMAW based on FLUENT

(2013) Xueping Ding et al.   Acta Metallurgica Sinica-English Letters

A droplet in the inter-electrode gap during gas metal arc welding

(2011) Valerian Nemchinsky   JOURNAL OF PHYSICS D-APPLIED PHYSICS