A method for determining r-value of aluminum sheets with the Portevin-Le Chatelier effect

Effects of high Mg content and processing parameters on Portevin-Le Chatelier and negative strain rate sensitivity effects in Al–Mg alloys

(2020) Chang-Hee Cho et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Experimental investigation of a Portevin-Le Chatelier band in Ni‒Co-based superalloys in relation to γʹ precipitates at 500 ℃

(2020) Yanke Liu et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

Zn/Cu regulated critical strain and serrated flow behavior in Al–Mg alloys

(2020) Yingxin Geng et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Temperature-Dependent Macroscopic Mechanical Behaviors and Their Microscopic Explanations in a Medium Mn Steel

(2020) Jiawei Ma et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Propagating bands of plastic deformation in a metal alloy as critical avalanches

(2020) Tero Mäkinen et al.   Science Advances

Estimation of Texture-Dependent Stress-Strain Curve and r-Value of Aluminum Alloy Sheet Using Deep Learning

(2020) Kohta Koenuma et al.   MATERIALS TRANSACTIONS

Macroscopic consequences of Piobert–Lüders and Portevin–Le Chatelier bands during tensile deformation in Al-Mg alloys

(2019) Baptiste Reyne et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Spatiotemporal correlations in the Portevin-Le Chatelier band dynamics during the type B - type C transition

(2019) M. Mehenni et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Mechanical properties, springback, and formability of W-temper and peak aged 7075 aluminum alloy sheets: Experiments and modeling

(2019) Yumi Choi et al.   INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES

Experimental study of Portevin–Le Châtelier bands on tensile and plane strain tensile tests

(2018) Ndeye Awa Sene et al.   Archives of Civil and Mechanical Engineering

Analysis of cup earing for AA3104-H19 aluminum alloy sheet

(2018) Y. Shi et al.   EUROPEAN JOURNAL OF MECHANICS A-SOLIDS

Plastic anisotropy and failure in thin metal: Material characterization and fracture prediction with an advanced constitutive model and polar EPS (effective plastic strain) fracture diagram for AA 3014-H19

(2018) Robert E. Dick et al.   INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES

Effect of microstructure on continuous propagation of the Portevin–Le Chatelier deformation bands

(2017) D. Yuzbekova et al.   INTERNATIONAL JOURNAL OF PLASTICITY

Discontinuous strain-induced martensite transformation related to the Portevin-Le Chatelier effect in a medium manganese steel

(2017) Binhan Sun et al.   SCRIPTA MATERIALIA

Calorimetric signature of the Portevin–Le Châtelier effect in an aluminum alloy from infrared thermography measurements and heat source reconstruction

(2016) D. Delpueyo et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Characterization of the deformation behaviors associated with the serrated flow of a 5456 Al-based alloy using two orthogonal digital image correlation systems

(2016) Y.L. Cai et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Study on the out-of-plane deformation of the Portevin–Le Chatelier band by using digital shearography

(2015) Shihua Fu et al.   MEASUREMENT

Spatio-temporal characteristics of plastic instability in AA5182-O during biaxial deformation

(2015) Junying Min et al.   MATERIALS & DESIGN

Tensile behavior of 3104 aluminum alloy processed by homogenization and cryogenic treatment

(2014) Wen-da ZHANG et al.   TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA

Texture effects on development of shear bands in rolled AZ31 alloy

(2012) Y.B. Chun et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Analytical derivation of earing in circular cup drawing based on simple tension properties

(2011) Kwansoo Chung et al.   EUROPEAN JOURNAL OF MECHANICS A-SOLIDS

Analytical Approach to Predict Anisotropic Material Properties from Cup Drawings

(2008) J. W. Yoon et al.   International Journal of Material Forming