Microstructure and mechanical properties of Al/Mg/Al composite sheets containing trapezoidal shaped intermediate layer

Microstructure and mechanical properties of ultra-lightweight Mg-Li-Al/Al-Li composite produced by accumulative roll bonding at ambient temperature

(2020) Yang Wang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Effects of annealing on the interfacial structures and mechanical properties of hot roll bonded Al/Mg clad sheets

(2020) Pengju Wang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Quench sensitivity characterization of a LPSO-phase containing Mg alloy

(2019) Dan Wang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Effect of solute content and temperature on the deformation mechanisms and critical resolved shear stress in Mg-Al and Mg-Zn alloys

(2019) J.-Y. Wang et al.   ACTA MATERIALIA

Study on Al/Mg/Al sheet fabricated by combination of porthole die co-extrusion and subsequent hot rolling

(2019) Jianwei Tang et al.   JOURNAL OF ALLOYS AND COMPOUNDS

On the role of Laves phases on the mechanical properties of Mg-Al-Ca alloys

(2019) M. Zubair et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Fabrication, microstructure and mechanical properties of the as-rolled ZW31/PMMCs laminate

(2019) Xuan-chang Zhang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Microstructural evolution and mechanical behavior of Mg/Al laminated composite sheet by novel corrugated rolling and flat rolling

(2019) Tao Wang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Research on the microstructure and properties of a multi-pass friction stir processed 6061Al coating for AZ31 Mg alloy

(2019) Xiaoming Xiong et al.   Journal of Magnesium and Alloys

Microstructure and tensile properties of magnesium matrix nanocomposite reinforced by high mass fraction of nano-sized particles including TiC and MgZn2

(2019) Kai-bo Nie et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Microstructure evolution and mechanical properties of an AA6061/AZ31B alloy plate fabricated by explosive welding

(2018) Tingting Zhang et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Influence of micro-alloying with silver on microstructure and mechanical properties of Al-Cu alloy

(2018) Purnendu Kumar Mandal et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Influence of multi-pass rolling and subsequent annealing on the interface microstructure and mechanical properties of the explosive welding Mg/Al composite plates

(2018) Zhiqing Chen et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Effect of annealing on the microstructures and mechanical properties of Al/Mg/Al laminates

(2018) Huihui Nie et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Effect of deformation temperature on texture and mechanical properties of ZK60 magnesium alloy sheet rolled by multi-pass lowered-temperature rolling

(2018) Wenke Wang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Analysis of bending characteristics of bimetal steel composite

(2018) Zhou Li et al.   INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES

On the rule of mixtures for bimetal composites

(2017) Bo Feng et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Microstructure and mechanical anisotropy of the hot rolled Mg-8.1Al-0.7Zn-0.15Ag alloy

(2017) Longhui Mao et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Compressive mechanical behavior of Al/Mg composite rods with different types of Al sleeve

(2016) Bo Feng et al.   ACTA MATERIALIA

Effect of the steel sheet surface hardening state on interfacial bonding strength of embedded aluminum–steel composite sheet produced by cold roll bonding process

(2016) Chunyang Wang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Three-Ply Al/Mg/Al Clad Sheets Fabricated by Twin-Roll Casting and Post-treatments (Homogenization, Warm Rolling, and Annealing)

(2016) Jaeyeong Park et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Effects of annealing process on sagging resistance of cold-rolled three-layer Al alloy clad sheets

(2016) Yuan-yuan ZHAO et al.   TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA

Microstructures and mechanical properties of Mg–Al–Ca alloys affected by Ca/Al ratio

(2015) Li Zhang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Improvement of interfacial bonding strength in roll-bonded Mg/Al clad sheets through annealing and secondary rolling process

(2015) Jung-Su Kim et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Microstructure and mechanical properties of Al/Ti/Al laminated composites prepared by roll bonding

(2015) M. Ma et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Microstructure and mechanical behavior of a Mg AZ31/Al 7050 laminate composite fabricated by extrusion

(2015) Yang Wu et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Growth kinetics of Al–Fe intermetallic compounds during annealing treatment of friction stir lap welds

(2014) M. Movahedi et al.   MATERIALS CHARACTERIZATION

Influence of secondary warm rolling on the interface microstructure and mechanical properties of a roll-bonded three-ply Al/Mg/Al sheet

(2014) K.S. Lee et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Effect of high temperature annealing and subsequent hot rolling on microstructural evolution at the bond-interface of Al/Mg/Al alloy laminated composites

(2013) Changzeng Luo et al.   MATERIALS CHARACTERIZATION

A novel testing approach for interfacial normal bond strength of thin laminated metallic composite plates

(2013) Jianjun Zhang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Interfacial microstructure, bonding strength and fracture of magnesium–aluminum laminated composite plates fabricated by direct hot pressing

(2011) Bo Zhu et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Mechanical properties of an Al/Mg/Al trilaminated composite fabricated by hot rolling

(2010) X. P. Zhang et al.   JOURNAL OF MATERIALS SCIENCE