Dynamic mechanical properties of 316L stainless steel fabricated by an additive manufacturing process

Effect of initial microstructure on the deformation heterogeneities of 316L stainless steels fabricated by selective laser melting processing

(2020) Amol B. Kale et al.   Journal of Materials Research and Technology-JMR&T

Investigation into the dynamic mechanical properties of selective laser melted Ti-6Al-4V alloy at high strain rate tensile loading

(2019) Liu Yang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Strength analysis of Ti6Al4V titanium alloy produced by the use of additive manufacturing method under static load conditions

(2019) Karolina Karolewska et al.   Journal of Materials Research and Technology-JMR&T

Characterization and mechanical properties of cladded stainless steel 316L with nuclear applications fabricated using electron beam melting

(2018) I.A. Segura et al.   JOURNAL OF NUCLEAR MATERIALS

Strain rate effect on the tension and compression stress-state asymmetry for electron beam additive manufactured Ti6Al4V

(2018) Omar L. Rodriguez et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Correlation between process parameters, microstructure and properties of 316 L stainless steel processed by selective laser melting

(2018) Tomasz Kurzynowski et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

High Strength and Ductility of Additively Manufactured 316L Stainless Steel Explained

(2018) Md. Shamsujjoha et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Mechanism of high yield strength and yield ratio of 316 L stainless steel by additive manufacturing

(2018) Y.J. Yin et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Grain refinement of wire arc additively manufactured titanium by the addition of silicon

(2017) S. Mereddy et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Characterization the contribution and limitation of the characteristic processing parameters in cold metal transfer deposition of an Al alloy

(2017) Peng Wang et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Study on microstructure, mechanical properties and machinability of efficiently additive manufactured AISI 316L stainless steel by high-power direct laser deposition

(2017) Peng Guo et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Preliminary investigation on selective laser melting of Ti-5Al-2.5Sn α-Ti alloy: From single tracks to bulk 3D components

(2017) Kaiwen Wei et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Effect of CaF 2 addition on macro/microstructures and mechanical properties of wire and arc additive manufactured Ti-6Al-4V components

(2017) Bo Yin et al.   MATERIALS LETTERS

Twinning induced plasticity in austenitic stainless steel 316L made by additive manufacturing

(2017) M.S. Pham et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Microstructure and mechanical properties of the austenitic stainless steel 316L fabricated by gas metal arc additive manufacturing

(2017) Xiaohui Chen et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Additively manufactured hierarchical stainless steels with high strength and ductility

(2017) Y. Morris Wang et al.   NATURE MATERIALS

Mechanical properties and dynamic constitutive model of 42CrMo steel

(2017) Zhiwu Zhu et al.   MATERIALS & DESIGN

Influence of heat-treatment on the dynamic behavior of 3D laser-deposited Ti–6Al–4V alloy

(2016) Jin Yao et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Crack path selection at the interface of wrought and wire+arc additive manufactured Ti–6Al–4V

(2016) Jikui Zhang et al.   MATERIALS & DESIGN

Microstructural evolution and mechanical properties of Ti-6Al-4V wall deposited by pulsed plasma arc additive manufacturing

(2016) J.J. Lin et al.   MATERIALS & DESIGN

Effect of arc mode in cold metal transfer process on porosity of additively manufactured Al-6.3%Cu alloy

(2014) Baoqiang Cong et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Effect of stacking-fault energy on deformation twin thickness in Cu–Al alloys

(2008) Y. Zhang et al.   SCRIPTA MATERIALIA