Evaluation of the gas porosity and mechanical properties of vacuum assisted pore-free die-cast Al-Si-Cu alloy

Effect of short T6 heat treatment on the microstructure and the mechanical properties of newly developed die-cast Al–Si–Mg–Mn alloys

(2020) Qing Cai et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Microstructure and properties of AlSi12Fe alloy high pressure die-castings under different vacuum levels

(2020) Chen Hu et al.   VACUUM

Specific Response of Additively Manufactured AlSi9Cu3Fe Alloy to Precipitation Strengthening

(2019) Michaela Roudnická et al.   METALS AND MATERIALS INTERNATIONAL

Kinetic analysis of pore formation in die-cast metals and influence of absolute pressure on porosity

(2019) Hanxue Cao et al.   VACUUM

Microstructure evolution and mechanical properties of new die-cast Al-Si-Mg-Mn alloys

(2019) Qing Cai et al.   MATERIALS & DESIGN

Effect of vacuum degree and T6 treatment on the microstructure and mechanical properties of Al–Si–Cu alloy die castings

(2019) Hanxue Cao et al.   VACUUM

On the formation mechanism of the ring-like microstructure of high-pressure die-cast A390 alloy

(2018) J. Wang et al.   MATERIALS CHARACTERIZATION

The influence of different vacuum degree on the porosity and mechanical properties of aluminum die casting

(2017) Hanxue Cao et al.   VACUUM

Effect of the Plunger Velocity and the Fast Shot Set Point on the Gas Porosity during ADC12 Plate Die Casting

(2016) Ik Min Park et al.   Korean Journal of Metals and Materials

Effect of solution heat treatment on gas porosity and mechanical properties in a die cast step test part manufactured with a new AlSi10MnMg(Fe) secondary alloy

(2016) A. Niklas et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Effect of Gas Bubbling Filtration Treatment on Microporosity Variation in A356 Aluminium Alloy

(2016) Choongdo Lee et al.   Acta Metallurgica Sinica-English Letters

Conditions for blister formation during thermal cycles of Al–Si–Cu–Fe alloys for high pressure die-casting

(2016) Oksana Ozhoga-Maslovskaja et al.   MATERIALS & DESIGN

Vacuum Die Casting Process and Simulation for Manufacturing 0.8 mm-Thick Aluminum Plate with Four Maze Shapes

(2015) Chul Jin et al.   Metals

Effect of heat treatment and Fe content on the microstructure and mechanical properties of die-cast Al–Si–Cu alloys

(2015) Hailin Yang et al.   MATERIALS & DESIGN

A study of the mechanical properties of an Al–Si–Cu alloy (ADC12) produced by various casting processes

(2012) M. Okayasu et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Improvements engineered in UTS and elongation of aluminum alloy high pressure die castings through the alteration of runner geometry and plunger velocity

(2012) D.R. Gunasegaram et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Compression Behavior of Entrapped Gas in High Pressure Diecasting

(2012) Yasushi Iwata et al.   MATERIALS TRANSACTIONS

Fabrication by vacuum die casting and simulation of aluminum bipolar plates with micro-channels on both sides for proton exchange membrane (PEM) fuel cells

(2011) Chul Kyu Jin et al.   INTERNATIONAL JOURNAL OF HYDROGEN ENERGY

Gas content in high pressure die castings

(2011) Laihua Wang et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Fabrication process analysis and experimental verification for aluminum bipolar plates in fuel cells by vacuum die-casting

(2011) Chul Kyu Jin et al.   JOURNAL OF POWER SOURCES

The thickness of defect bands in high-pressure die castings

(2009) S. Otarawanna et al.   MATERIALS CHARACTERIZATION

Experimental and numerical analysis of gas entrapment defects in plate ADC12 die castings

(2008) H.D. Zhao et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Optimization of porosity formation in AlSi9Cu3 pressure die castings using genetic algorithm analysis

(2008) V.D. Tsoukalas   MATERIALS & DESIGN