Correlation of Microstructural Evolution with Mechanical and Tribological Behaviour of SS 304 Specimens Developed Through SLM Technique

Influence of heat treatment temperature on the microstructural, mechanical, and wear behavior of 316L stainless steel fabricated by laser powder bed additive manufacturing

(2020) Emre Tascioglu et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Microstructure, tensile properties and mechanical anisotropy of selective laser melted 304L stainless steel

(2020) Juan Hou et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

Pure copper components fabricated by cold spray (CS) and selective laser melting (SLM) technology

(2020) Jian Huang et al.   SURFACE & COATINGS TECHNOLOGY

Effect of Heat-Treatment on the Microstructure, Mechanical Properties and Corrosion Behaviour of SS 316 Structures Built by Laser Directed Energy Deposition Based Additive Manufacturing

(2020) K. Benarji et al.   METALS AND MATERIALS INTERNATIONAL

Microstructure and tribological evolution during laser alloying WC-12%Co and Cr3C2−25%NiCr powders on nodular iron surface

(2019) N. Jeyaprakash et al.   Results in Physics

Influence of B4C nanoparticles on mechanical behaviour of Silicon brass nanocomposite through mechanical alloying and hot pressing

(2019) R. Clinktan et al.   CERAMICS INTERNATIONAL

Post-Processing Effects on Surface Properties of Direct Metal Laser Sintered AlSi10Mg Parts

(2019) Binnur Sagbas   METALS AND MATERIALS INTERNATIONAL

Characterization and tribological evaluation of NiCrMoNb and NiCrBSiC laser cladding on near-α titanium alloy

(2019) N. Jeyaprakash et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Investigation of effects of process parameters on microstructure and hardness of SLM manufactured SS316L

(2018) Wakshum M. Tucho et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Additive manufacturing of WC reinforced maraging steel 300 composites by cold spraying and selective laser melting

(2018) Xingchen Yan et al.   SURFACE & COATINGS TECHNOLOGY

Microstructure and Mechanical Characterization of Friction-Stir-Welded 316L Austenitic Stainless Steels

(2018) R. Ramesh et al.   JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE

Effect of selective laser melting (SLM) process parameters on microstructure and mechanical properties of 316L austenitic stainless steel

(2017) E. Liverani et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Additively manufactured hierarchical stainless steels with high strength and ductility

(2017) Y. Morris Wang et al.   NATURE MATERIALS

The microstructure, mechanical properties and corrosion resistance of 316L stainless steel fabricated using laser engineered net shaping

(2016) Michał Ziętala et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Effects of tailored gradient interface on wear properties of WC/Inconel 718 composites using selective laser melting

(2016) Ting Rong et al.   SURFACE & COATINGS TECHNOLOGY

Microstructure and mechanical properties of the near-beta titanium alloy Ti-5553 processed by selective laser melting

(2016) H. Schwab et al.   MATERIALS & DESIGN

Dislocation Strengthening without Ductility Trade-off in Metastable Austenitic Steels

(2016) Jiabin Liu et al.   Scientific Reports

Mechanical and Microstructural Investigation of Nickel-Based Superalloy IN718 Manufactured by Selective Laser Melting (SLM)

(2015) Johannes Strößner et al.   ADVANCED ENGINEERING MATERIALS

Microstructure Characteristics of Inconel 625 Superalloy Manufactured by Selective Laser Melting

(2015) Shuai Li et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

Additive Manufacturing Technologies – Rapid Prototyping to Direct Digital Manufacturing

(2014) Bernhard Mueller   ASSEMBLY AUTOMATION

Additive Manufacturing: Making Imagination the Major Limitation

(2014) Yuwei Zhai et al.   JOM

Surface hardness improvement of plasma-sprayed AISI 316L stainless steel coating by low-temperature plasma carburizing

(2013) Shinichiro Adachi et al.   ADVANCED POWDER TECHNOLOGY

Metallic additive manufacturing: state-of-the-art review and prospects

(2012) Benjamin Vayre et al.   Mechanics & Industry