Effect of tool-electrode material in through-hole formation using ECDM process

Micro-machining through electrochemical discharge processes: a review

(2020) Nitesh Kumar et al.   MATERIALS AND MANUFACTURING PROCESSES

Performance of magnetic field-assisted citric acid electrolyte on electrochemical micro-machining of SS 316L

(2020) J.R. Vinod Kumaar et al.   MATERIALS AND MANUFACTURING PROCESSES

Influence of tool electrode feed rate in the electrochemical discharge drilling of a glass substrate

(2020) Julfekar Arab et al.   MATERIALS AND MANUFACTURING PROCESSES

Reverse EDM process for pattern generation using powder metallurgical green compact tool

(2020) Rashed Mustafa Mazarbhuiya et al.   MATERIALS AND MANUFACTURING PROCESSES

Magnetic field and ultrasonic aided laser drilling effect on Ti6Al4V microstructural characteristics

(2020) Soheil Amiri et al.   MATERIALS AND MANUFACTURING PROCESSES

Measurement and analysis of the geometric characteristics of microholes and tool wear for varying tool-workpiece gaps in electrochemical discharge drilling

(2020) Julfekar Arab et al.   MEASUREMENT

Numerical and experimental investigations into microchannel formation in glass substrate using electrochemical discharge machining

(2019) Dileep Kumar Mishra et al.   JOURNAL OF MICROMECHANICS AND MICROENGINEERING

Fabrication of multiple through-holes in non-conductive materials by Electrochemical Discharge Machining for RF MEMS Packaging

(2019) Julfekar Arab et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Investigation on EDM machining of Ti6Al4V with negative polarity brass electrode

(2019) Saurabh Nair et al.   MATERIALS AND MANUFACTURING PROCESSES

Effect of tool electrode roughness on the geometric characteristics of through-holes formed by ECDM

(2019) Julfekar Arab et al.   PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY

Numerical and experimental analysis of high-aspect-ratio micro-tool electrode fabrication using controlled electrochemical machining

(2019) Subrat Kumar Patro et al.   JOURNAL OF APPLIED ELECTROCHEMISTRY

Experimental investigation on wire electric discharge machining (WEDM) of Nimonic C-263 superalloy

(2018) Himanshu Bisaria et al.   MATERIALS AND MANUFACTURING PROCESSES

Electrochemical micromachining of micro square pattern using reusable masked tool

(2018) S. Kunar et al.   MATERIALS AND MANUFACTURING PROCESSES

Fabrication of precise microchannels using a side-insulated tool in a spark assisted chemical engraving process

(2017) S. Saranya et al.   MATERIALS AND MANUFACTURING PROCESSES

Effect of ultrasonic vibration on the single discharge of electrochemical discharge machining

(2017) S. Elhami et al.   MATERIALS AND MANUFACTURING PROCESSES

On pressurized feeding approach for effective control on working gap in ECDM

(2017) Tarlochan Singh et al.   MATERIALS AND MANUFACTURING PROCESSES

Micro-Hole Drilling on Glass Substrates—A Review

(2017) Lucas Hof et al.   Micromachines

Study of tool trajectory in blisk channel ECM with spiral feeding

(2016) Juchen Zhang et al.   MATERIALS AND MANUFACTURING PROCESSES

Electrochemical Discharge Machining Micro-Hole in Stainless Steel with Tool Electrode High-Speed Rotating

(2014) S. F. Huang et al.   MATERIALS AND MANUFACTURING PROCESSES

Experimental Study of Traveling Wire Electrochemical Spark Machining of Borosilicate Glass

(2013) Basanta Kumar Bhuyan et al.   MATERIALS AND MANUFACTURING PROCESSES

Tool wear and tool thermal expansion during micro-machining by spark assisted chemical engraving

(2011) Jana D. Abou Ziki et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Intelligent Modeling and Multiobjective Optimization of Die Sinking Electrochemical Spark Machining Process

(2011) Mohan Charan Panda et al.   MATERIALS AND MANUFACTURING PROCESSES

Effect of surface roughness of tool electrode materials in ECDM performance

(2010) Cheng-Kuang Yang et al.   INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE

Effects of Process Parameters on Hole Circularity and Taper in Pulsed Nd:YAG Laser Microdrilling of Tin-Al2O3Composites

(2010) Ranjib Biswas et al.   MATERIALS AND MANUFACTURING PROCESSES

Gas film formation time and gas film life time during electrochemical discharge phenomenon

(2009) Anis Allagui et al.   ELECTROCHIMICA ACTA

The effect of thermal conductivity of the tool electrode in spark-assisted chemical engraving gravity-feed micro-drilling

(2008) M Mousa et al.   JOURNAL OF MICROMECHANICS AND MICROENGINEERING

Deep plasma etching of glass with a silicon shadow mask

(2007) K. Kolari   SENSORS AND ACTUATORS A-PHYSICAL