Development of Thermo Mechanical Model for Prediction of Temperature Diffusion in Different FSW Tool Pin Geometries During Joining of AZ80A Mg Alloys

Peak Temperature Correlation and Temperature Distribution during Joining of AZ80A Mg Alloy by FSW – A Numerical and Experimental Investigation

(2020) p Sevvel et al.   STROJNISKI VESTNIK-JOURNAL OF MECHANICAL ENGINEERING

Simulation of heat transfer and analysis of impact of tool pin geometry and tool speed during friction stir welding of AZ80A Mg alloy plates

(2020) S. D. Dhanesh Babu et al.   Journal of Mechanical Science and Technology

GENERATION OF REGRESSION MODELS AND MULTI RESPONSE OPTIMIZATION OF FSW TECHNIQUE PARAMETERS DURING FABRICATION OF AZ80A Mg ALLOY JOINTS

(2019) P Sevvel et al.   TRANSACTIONS OF THE CANADIAN SOCIETY FOR MECHANICAL ENGINEERING

Improving friction stir weldability of Al/Mg alloys via ultrasonically diminishing pin adhesion

(2018) Xiangchen Meng et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

Mechanical properties’ modification of large load friction stir welded AZ31B Mg alloy joint

(2018) Nan Xu et al.   MATERIALS LETTERS

Numerical modelling and experimental investigation of thermal and material flow in probeless friction stir spot welding process of Al 2198-T8

(2018) Xiawei Yang et al.   SCIENCE AND TECHNOLOGY OF WELDING AND JOINING

Equations of heat generation during friction stir welding for tapered polygonal tools

(2018) Basim M. A. Al Bhadle et al.   SCIENCE AND TECHNOLOGY OF WELDING AND JOINING

INFLUENCE OF THE TOOL ROTATIONAL SPEED ON THE MICROSTRUCTURAL CHARACTERISTICS OF DISSIMILAR MG ALLOYS DURING FSW

(2018) P Sevvel et al.   TRANSACTIONS OF THE CANADIAN SOCIETY FOR MECHANICAL ENGINEERING

Role of tool rotational speed in influencing microstructural evolution, residual-stress formation and tensile properties of friction-stir welded AZ80A Mg alloy

(2018) P. Sevvel et al.   Materiali in Tehnologije

Effect of welding parameters on the microstructure and mechanical properties of the friction stir welded joints of a Mg-12Li-1Al alloy

(2017) Seyed Alireza Askariani et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Microstructure-based modeling of tensile deformation of a friction stir welded AZ31 Mg alloy

(2017) Weijun He et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Influence of metallic foil alloying by FSW process on mechanical properties and metallurgical characterization of AM20 Mg alloy

(2017) Prakash Kumar Sahu et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Friction-stir lap-joining of aluminium-magnesium/poly-methyl-methacrylate hybrid structures: thermo-mechanical modelling and experimental feasibility study

(2017) H. Aghajani Derazkola et al.   SCIENCE AND TECHNOLOGY OF WELDING AND JOINING

Review of research progress on aluminium–magnesium dissimilar friction stir welding

(2017) L. H. Shah et al.   SCIENCE AND TECHNOLOGY OF WELDING AND JOINING

Effects of microstructural asymmetries across friction stir welded AA2024 joints on mechanical properties

(2017) Pengliang Niu et al.   SCIENCE AND TECHNOLOGY OF WELDING AND JOINING

Microstructural characteristics and mechanical properties of the dissimilar friction-stir butt welds between an Al–Mg alloy and A316L stainless steel

(2016) R . Rafiei et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Computational Fluid Dynamics Modeling on Steady-State Friction Stir Welding of Aluminum Alloy 6061 to TRIP Steel

(2016) Xun Liu et al.   JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME

Investigations of tool tilt angle on properties friction stir welding of A441 AISI to AA1100 aluminium

(2016) Majid Elyasi et al.   PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE

An analytical model to calculate the peak temperature for friction stir welding

(2016) Jinwen Qian et al.   SCIENCE AND TECHNOLOGY OF WELDING AND JOINING

A numerical comparison of the flow behaviour in Friction Stir Welding (FSW) using unworn and worn tool geometries

(2015) A.F. Hasan et al.   MATERIALS & DESIGN

An analytical model of steady-state continuous drive friction welding

(2013) J.T. Xiong et al.   ACTA MATERIALIA

Investigations of friction stir welding process using finite element method

(2013) Kadir Gök et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

A new smoothed particle hydrodynamics non-Newtonian model for friction stir welding: Process modeling and simulation of microstructure evolution in a magnesium alloy

(2013) Wenxiao Pan et al.   INTERNATIONAL JOURNAL OF PLASTICITY

Effects of Alloying Elements on Stacking Fault Energies and Electronic Structures of Binary Mg Alloys: A First-Principles Study

(2013) William Yi Wang et al.   Materials Research Letters

Friction-stir dissimilar welding of aluminium alloy to high strength steels: Mechanical properties and their relation to microstructure

(2012) R.S. Coelho et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

High strength lap joint of aluminium and stainless steels fabricated by friction stir welding with cutting pin

(2012) J T Xiong et al.   SCIENCE AND TECHNOLOGY OF WELDING AND JOINING

Numerical Analysis of Joint Temperature Evolution During Friction Stir Welding Based on Sticking Contact

(2011) Wenya Li et al.   JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE

Analysis of transient temperature and residual thermal stresses in friction stir welding of aluminum alloy 6061-T6 via numerical simulation

(2010) Mohammad Riahi et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Friction stir diffusion bonding of dissimilar metals

(2010) M. Girard et al.   SCIENCE AND TECHNOLOGY OF WELDING AND JOINING