On the Post-Printing Heat Treatment of a Wire Arc Additively Manufactured ER70S Part
Published 2020 View Full Article
- Home
- Publications
- Publication Search
- Publication Details
Title
On the Post-Printing Heat Treatment of a Wire Arc Additively Manufactured ER70S Part
Authors
Keywords
-
Journal
Materials
Volume 13, Issue 12, Pages 2795
Publisher
MDPI AG
Online
2020-06-23
DOI
10.3390/ma13122795
References
Ask authors/readers for more resources
Related references
Note: Only part of the references are listed.- Diagnosis of the microstructural and mechanical properties of over century-old steel railway bridge components
- (2020) Maciej Kowal et al. ENGINEERING FAILURE ANALYSIS
- Comparison of microstructural characteristics and mechanical properties of shipbuilding steel plates fabricated by conventional rolling versus wire arc additive manufacturing
- (2020) Alireza Vahedi Nemani et al. Additive Manufacturing
- Interfacial bonding between a wire arc additive manufactured 420 martensitic stainless steel part and its wrought base plate
- (2020) Mahya Ghaffari et al. MATERIALS CHEMISTRY AND PHYSICS
- Correlation of Microstructure and Mechanical Properties of Metal Big Area Additive Manufacturing
- (2019) Benjamin Shassere et al. Applied Sciences-Basel
- Effect of Solidification Defects and HAZ Softening on the Anisotropic Mechanical Properties of a Wire Arc Additive-Manufactured Low-Carbon Low-Alloy Steel Part
- (2019) Mahya Ghaffari et al. JOM
- Microstructural evolution and mechanical properties of a low-carbon low-alloy steel produced by wire arc additive manufacturing
- (2019) Mehran Rafieazad et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- On the toughness scatter in low alloy C-Mn steel samples fabricated using wire arc additive manufacturing
- (2018) Niyanth Sridharan et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Microstructure and properties of die steel fabricated by WAAM using H13 wire
- (2018) Tingting Wang et al. VACUUM
- Effect of heat treatment on the microstructure and anisotropy in mechanical properties of A357 alloy produced by selective laser melting
- (2018) Kun V. Yang et al. MATERIALS & DESIGN
- Fabrication of inclined thin-walled parts in multi-layer single-pass GMAW-based additive manufacturing with flat position deposition
- (2017) Jun Xiong et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Microstructural evolution and mechanical properties of maraging steel produced by wire + arc additive manufacture process
- (2017) Xiangfang Xu et al. MATERIALS CHARACTERIZATION
- Selective laser melting-wire arc additive manufacturing hybrid fabrication of Ti-6Al-4V alloy: Microstructure and mechanical properties
- (2017) Xuezhi Shi et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Material properties of CMT—metal additive manufactured duplex stainless steel blade-like geometries
- (2017) Gerhard Posch et al. Welding in the World
- Effect of processing parameters on microstructure and tensile properties of austenitic stainless steel 304L made by directed energy deposition additive manufacturing
- (2016) Zhuqing Wang et al. ACTA MATERIALIA
- Closed-loop control of variable layer width for thin-walled parts in wire and arc additive manufacturing
- (2016) Jun Xiong et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Influence of martensite-austenite (MA) on impact toughness of X80 line pipe steels
- (2016) Nazmul Huda et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Microstructure and anisotropic tensile behavior of laser additive manufactured TC21 titanium alloy
- (2016) Qiang Zhang et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Diffraction and single-crystal elastic constants of Inconel 625 at room and elevated temperatures determined by neutron diffraction
- (2016) Zhuqing Wang et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Wire + Arc Additive Manufacturing
- (2016) S. W. Williams et al. MATERIALS SCIENCE AND TECHNOLOGY
- A comparative study of additive manufacturing techniques: Residual stress and microstructural analysis of CLAD and WAAM printed Ti–6Al–4V components
- (2016) Blanka A. Szost et al. MATERIALS & DESIGN
- Anisotropic tensile behavior of Ti–6Al–4V components fabricated with directed energy deposition additive manufacturing
- (2015) Beth E. Carroll et al. ACTA MATERIALIA
- Review of Mechanical Properties of Ti-6Al-4V Made by Laser-Based Additive Manufacturing Using Powder Feedstock
- (2015) Allison M. Beese et al. JOM
- In situ formation of substrate release mechanisms for gas metal arc weld metal 3-D printing
- (2015) Amberlee S. Haselhuhn et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Metal Additive Manufacturing: A Review
- (2014) William E. Frazier JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
- Strong morphological and crystallographic texture and resulting yield strength anisotropy in selective laser melted tantalum
- (2013) Lore Thijs et al. ACTA MATERIALIA
- Influence of the Flame Straightening Process on Microstructural, Mechanical and Fracture Properties of S235 JR, S460 ML and S690 QL Structural Steels
- (2013) R. Lacalle et al. EXPERIMENTAL MECHANICS
- Effects of microstructure alteration on corrosion behavior of welded joint in API X70 pipeline steel
- (2012) Sajjad Bordbar et al. MATERIALS & DESIGN
- The Effect of Processing Conditions and Cooling Rate on the Microstructure and Properties of API X-70 and API X-100 Steels
- (2010) X. Yang et al. MATERIALS AND MANUFACTURING PROCESSES
- Transformation behavior and microstructural characteristics of acicular ferrite in linepipe steels
- (2007) Young Min Kim et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
Find the ideal target journal for your manuscript
Explore over 38,000 international journals covering a vast array of academic fields.
SearchCreate your own webinar
Interested in hosting your own webinar? Check the schedule and propose your idea to the Peeref Content Team.
Create Now