Fatigue assessment of as‐built and heat‐treated Inconel 718 specimens produced by additive manufacturing including notch effects

High cycle fatigue behavior and life prediction for additively manufactured 17-4 PH stainless steel: Effect of sub-surface porosity and surface roughness

(2020) Simone Romano et al.   THEORETICAL AND APPLIED FRACTURE MECHANICS

The effect of defects and notches in quasi-static and fatigue loading of Inconel 718 specimens produced by selective laser melting

(2020) Klas Solberg et al.   INTERNATIONAL JOURNAL OF FATIGUE

Fatigue behavior and microstructural evolution of additively manufactured Inconel 718 under cyclic loading at elevated temperature

(2020) P.D. Nezhadfar et al.   INTERNATIONAL JOURNAL OF FATIGUE

An analysis of fatigue failure mechanisms in an additively manufactured and shot peened IN 718 nickel superalloy

(2020) Enrico Salvati et al.   MATERIALS & DESIGN

High cycle fatigue life estimation of materials processed by laser powder bed fusion

(2019) Even W. Hovig et al.   FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES

Fatigue of additively manufactured 316L stainless steel: The influence of porosity and surface roughness

(2019) Klas Solberg et al.   FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES

Smooth and notch fatigue behavior of selectively laser melted Inconel 718 with as-built surfaces

(2019) Gianni Nicoletto   INTERNATIONAL JOURNAL OF FATIGUE

Laser Powder Bed Fusion of Inconel 718: Residual Stress Analysis Before and After Heat Treatment

(2019) Rafael Barros et al.   Metals

Influence of surface conditions and specimen orientation on high cycle fatigue properties of Inconel 718 prepared by laser powder bed fusion

(2019) David B. Witkin et al.   INTERNATIONAL JOURNAL OF FATIGUE

On the size and orientation effect in additive manufactured Ti-6Al-4V

(2019) D. Barba et al.   MATERIALS & DESIGN

A review of mechanical properties of additively manufactured Inconel 718

(2019) E. Hosseini et al.   Additive Manufacturing

A diagram for capturing and predicting failure locations in notch geometries produced by additive manufacturing

(2019) Klas Solberg et al.   INTERNATIONAL JOURNAL OF FATIGUE

Enhancing Fatigue Strength of Selective Laser Melting-Fabricated Inconel 718 by Tailoring Heat Treatment Route

(2018) Hong-Yuan Wan et al.   ADVANCED ENGINEERING MATERIALS

Notched fatigue testing of Inconel 718 prepared by selective laser melting

(2018) D.B. Witkin et al.   FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES

Significance of hot isostatic pressing (HIP) on multiaxial deformation and fatigue behaviors of additive manufactured Ti-6Al-4V including build orientation and surface roughness effects

(2018) Reza Molaei et al.   INTERNATIONAL JOURNAL OF FATIGUE

Defect analysis and fatigue design basis for Ni-based superalloy 718 manufactured by selective laser melting

(2018) Yoichi Yamashita et al.   INTERNATIONAL JOURNAL OF FATIGUE

Influence of defects and as-built surface roughness on fatigue properties of additively manufactured Alloy 718

(2018) Arun Ramanathan Balachandramurthi et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Notch-defect interaction in additively manufactured Inconel 718

(2018) K. Solberg et al.   INTERNATIONAL JOURNAL OF FATIGUE

Fatigue life of additively manufactured Ti–6Al–4V in the very high cycle fatigue regime

(2017) J. Günther et al.   INTERNATIONAL JOURNAL OF FATIGUE

Additive manufacturing of fatigue resistant materials: Challenges and opportunities

(2017) Aref Yadollahi et al.   INTERNATIONAL JOURNAL OF FATIGUE

Microstructure and hardness studies of Inconel 718 manufactured by selective laser melting before and after solution heat treatment

(2017) Wakshum M. Tucho et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

The Influence of Porosity on Fatigue Crack Initiation in Additively Manufactured Titanium Components

(2017) S. Tammas-Williams et al.   Scientific Reports

Critical assessment of the fatigue performance of additively manufactured Ti–6Al–4V and perspective for future research

(2016) P. Li et al.   INTERNATIONAL JOURNAL OF FATIGUE

On the microstructural and mechanical properties of post-treated additively manufactured Inconel 718 superalloy under quasi-static and cyclic loading

(2016) M.E. Aydinöz et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Fatigue Properties of Cast Magnesium Wheels

(2016) Zhenming Li et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Effect of standard heat treatment on the microstructure and mechanical properties of selective laser melting manufactured Inconel 718 superalloy

(2015) Dongyun Zhang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

The linear-elastic Theory of Critical Distances to estimate high-cycle fatigue strength of notched metallic materials at elevated temperatures

(2014) R. Louks et al.   FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES

The microstructure and mechanical properties of deposited-IN718 by selective laser melting

(2011) Zemin Wang et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Crack growth micro-mechanisms in the IN718 alloy under the combined influence of fatigue, creep and oxidation

(2009) D.G. Leo Prakash et al.   INTERNATIONAL JOURNAL OF FATIGUE

The theory of critical distances: a review of its applications in fatigue

(2007) Luca Susmel   ENGINEERING FRACTURE MECHANICS