Rafting‐Enabled Recovery Avoids Recrystallization in 3D‐Printing‐Repaired Single‐Crystal Superalloys
Published 2020 View Full Article
- Home
- Publications
- Publication Search
- Publication Details
Title
Rafting‐Enabled Recovery Avoids Recrystallization in 3D‐Printing‐Repaired Single‐Crystal Superalloys
Authors
Keywords
-
Journal
ADVANCED MATERIALS
Volume -, Issue -, Pages 1907164
Publisher
Wiley
Online
2020-02-20
DOI
10.1002/adma.201907164
References
Ask authors/readers for more resources
Related references
Note: Only part of the references are listed.- Hot cracking mechanism affecting a non-weldable Ni-based superalloy produced by selective electron Beam Melting
- (2018) Edouard Chauvet et al. ACTA MATERIALIA
- A modeling study of stress and strain formation induced during melting process in powder-bed electron beam melting for Ni superalloy
- (2018) Satoshi Tadano et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Additive Manufacturing of Nickel Superalloys: Opportunities for Innovation and Challenges Related to Qualification
- (2018) S. S. Babu et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- Microstructure and Mechanical Properties of CMSX-4 Single Crystals Prepared by Additive Manufacturing
- (2018) C. Körner et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- A peak position comparison method for high-speed quantitative Laue microdiffraction data processing
- (2018) Jiawei Kou et al. SCRIPTA MATERIALIA
- Mechanism of heat affected zone cracking in Ni-based superalloy DZ125L fabricated by laser 3D printing technique
- (2018) Yao Li et al. MATERIALS & DESIGN
- Peritectic titanium alloys for 3D printing
- (2018) Pere Barriobero-Vila et al. Nature Communications
- Experimental optimization of laser additive manufacturing process of single-crystal nickel-base superalloys by a statistical experiment design method
- (2017) Yao-Jian Liang et al. JOURNAL OF ALLOYS AND COMPOUNDS
- Additive manufacturing of metals: a brief review of the characteristic microstructures and properties of steels, Ti-6Al-4V and high-entropy alloys
- (2017) Stéphane Gorsse et al. SCIENCE AND TECHNOLOGY OF ADVANCED MATERIALS
- An experimental investigation into the stress and strain development of a Ni-base single crystal superalloy during cooling from solidification
- (2017) Chunlei Qiu et al. MATERIALS & DESIGN
- Microstructural control during laser additive manufacturing of single-crystal nickel-base superalloys: New processing–microstructure maps involving powder feeding
- (2017) Yao-Jian Liang et al. MATERIALS & DESIGN
- Microstructure of the Nickel-Base Superalloy CMSX-4 Fabricated by Selective Electron Beam Melting
- (2016) Markus Ramsperger et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- Additive Manufacturing of Single-Crystal Superalloy CMSX-4 Through Scanning Laser Epitaxy: Computational Modeling, Experimental Process Development, and Process Parameter Optimization
- (2016) Amrita Basak et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- Alloy design for aircraft engines
- (2016) Tresa M. Pollock NATURE MATERIALS
- Solution Heat Treatment of the Single Crystal Nickel-Base Superalloy CMSX-4 Fabricated by Selective Electron Beam Melting
- (2015) Markus Ramsperger et al. ADVANCED ENGINEERING MATERIALS
- Microstructure simulation on recrystallization of an as-cast nickel based single crystal superalloy
- (2015) Zhonglin Li et al. COMPUTATIONAL MATERIALS SCIENCE
- Numerical modeling of microstructure evolution during laser additive manufacturing of a nickel-based superalloy
- (2014) Pulin Nie et al. ACTA MATERIALIA
- Effects of stacking fault energy on the creep behaviors of Ni-base superalloy
- (2014) Chenggang Tian et al. MATERIALS & DESIGN
- Creep behavior under isothermal and non-isothermal conditions of AM3 single crystal superalloy for different solutioning cooling rates
- (2014) S. Steuer et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Temperature-dependent ideal strength and stacking fault energy of fcc Ni: a first-principles study of shear deformation
- (2012) S L Shang et al. JOURNAL OF PHYSICS-CONDENSED MATTER
- Measurement of the effective γ/γ′ lattice mismatch during high temperature creep of Ni-based single crystal superalloy
- (2012) Laura Dirand et al. MATERIALS CHARACTERIZATION
- Effect of cyclic recovery heat treatment on surface recrystallization of a directionally solidified superalloy
- (2012) Guang XIE et al. Progress in Natural Science-Materials International
- Microstructural and mechanical approaches of the selective laser melting process applied to a nickel-base superalloy
- (2011) T. Vilaro et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- The effect of alloying elements on the dislocation climbing velocity in Ni: A first-principles study
- (2009) Xiao-Xiang Yu et al. ACTA MATERIALIA
- A dedicated superbend x-ray microdiffraction beamline for materials, geo-, and environmental sciences at the advanced light source
- (2009) Martin Kunz et al. REVIEW OF SCIENTIFIC INSTRUMENTS
- Dislocation structures and their relationship to strength in deformed nickel microcrystals
- (2008) D.M. Norfleet et al. ACTA MATERIALIA
Become a Peeref-certified reviewer
The Peeref Institute provides free reviewer training that teaches the core competencies of the academic peer review process.
Get StartedAsk a Question. Answer a Question.
Quickly pose questions to the entire community. Debate answers and get clarity on the most important issues facing researchers.
Get Started