Rapid Solidification and Non-equilibrium Phase Constitution in Laser Powder Bed Fusion (LPBF) of AlSi10Mg Alloy: Analysis of Nano-precipitates, Eutectic Phases, and Hardness Evolution

A comparison of Selective Laser Melting with bulk rapid solidification of AlSi10Mg alloy

(2018) Silvia Marola et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Deformation mechanism during dynamic loading of an additively manufactured AlSi10Mg_200C

(2018) Amir Hadadzadeh et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Solidification pattern, microstructure and texture development in Laser Powder Bed Fusion (LPBF) of Al10SiMg alloy

(2018) Hong Qin et al.   MATERIALS CHARACTERIZATION

Microstructural characterization of cellular AlSi10Mg alloy fabricated by selective laser melting

(2018) Mulin Liu et al.   MATERIALS & DESIGN

Role of melt pool boundary condition in determining the mechanical properties of selective laser melting AlSi10Mg alloy

(2018) Z.H. Xiong et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Multiple precipitation pathways in an Al-7Si-0.6Mg alloy fabricated by selective laser melting

(2018) Jeremy H. Rao et al.   SCRIPTA MATERIALIA

Processing and characterization of continuous-cast AlMgSc(Zr) sheets for improved strength

(2017) Vahid Fallah et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Cluster evolution mechanisms during aging in Al–Mg–Si alloys

(2016) Vahid Fallah et al.   ACTA MATERIALIA

Characterization of an Aluminum Alloy Hemispherical Shell Fabricated via Direct Metal Laser Melting

(2016) T. G. Holesinger et al.   JOM

Rapid Solidification: Selective Laser Melting of AlSi10Mg

(2016) Ming Tang et al.   JOM

Effect of heat treatment on AlSi10Mg alloy fabricated by selective laser melting: Microstructure evolution, mechanical properties and fracture mechanism

(2016) Wei Li et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Addendum to: “Atomistic investigation of clustering phenomenon in the Al–Cu system: Three-dimensional phase-field crystal simulation and HRTEM/HRSTEM characterization” [Acta Mater. 61 (2013) 6372–6386]

(2015) Vahid Fallah et al.   ACTA MATERIALIA

Atomic-scale pathway of early-stage precipitation in Al–Mg–Si alloys

(2015) Vahid Fallah et al.   ACTA MATERIALIA

Selective laser melting of AlSi10Mg alloy: Process optimisation and mechanical properties development

(2015) Noriko Read et al.   MATERIALS & DESIGN

On the Precipitation Hardening of Selective Laser Melted AlSi10Mg

(2015) Nesma T. Aboulkhair et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Atomistic investigation of clustering phenomenon in the Al–Cu system: Three-dimensional phase-field crystal simulation and HRTEM/HRSTEM characterization

(2013) Vahid Fallah et al.   ACTA MATERIALIA

Selective laser sintering/melting (SLS/SLM) of pure Al, Al–Mg, and Al–Si powders: Effect of processing conditions and powder properties

(2013) E.O. Olakanmi   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Phase-field simulation of solidification morphology in laser powder deposition of Ti–Nb alloys

(2012) V. Fallah et al.   ACTA MATERIALIA

Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder

(2012) Lore Thijs et al.   ACTA MATERIALIA

Temporal development of melt-pool morphology and clad geometry in laser powder deposition

(2011) Vahid Fallah et al.   COMPUTATIONAL MATERIALS SCIENCE

Additive manufactured AlSi10Mg samples using Selective Laser Melting (SLM): Microstructure, high cycle fatigue, and fracture behavior

(2011) Erhard Brandl et al.   MATERIALS & DESIGN

Selective laser melting of aluminium components

(2010) Eleftherios Louvis et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY