The impact of thermoelectric leg geometries on thermal resistance and power output

Pulsed laser melting of bismuth telluride thermoelectric materials

(2019) Michael J. Carter et al.   Journal of Manufacturing Processes

Characterization of the thermo-mechanical properties of p-type (MnSi1.77) and n-type (Mg2Si0.6Sn0.4) thermoelectric materials

(2019) M. Mejri et al.   SCRIPTA MATERIALIA

Fabrication and Thermoelectric Properties of n-Type CoSb2.85Te0.15 Using Selective Laser Melting

(2018) Yonggao Yan et al.   ACS Applied Materials & Interfaces

Thermoelectric Higher Manganese Silicide: Synthetized, sintered and shaped simultaneously by selective laser sintering/Melting additive manufacturing technique

(2018) Yohann Thimont et al.   MATERIALS LETTERS

Laser additive manufacturing of powdered bismuth telluride

(2018) Haidong Zhang et al.   JOURNAL OF MATERIALS RESEARCH

Series of detail comparison and optimization of thermoelectric element geometry considering the PV effect

(2018) Samson Shittu et al.   RENEWABLE ENERGY

Preparation of n-type Bi2 Te3 thermoelectric materials by non-contact dispenser printing combined with selective laser melting

(2017) Keping Wu et al.   Physica Status Solidi-Rapid Research Letters

Non-equilibrium synthesis and characterization of n-type Bi2Te2.7Se0.3 thermoelectric material prepared by rapid laser melting and solidification

(2017) Yu Mao et al.   RSC Advances

Influences of energy density on microstructure and consolidation of selective laser melted bismuth telluride thermoelectric powder

(2017) Ahmed El-Desouky et al.   Journal of Manufacturing Processes

Design of a polymer thermoelectric generator using radial architecture

(2016) Akanksha K. Menon et al.   JOURNAL OF APPLIED PHYSICS

Radial thermoelectric generator fabricated from n- and p-type conducting polymers

(2016) Akanksha K. Menon et al.   JOURNAL OF APPLIED POLYMER SCIENCE

Rapid processing and assembly of semiconductor thermoelectric materials for energy conversion devices

(2016) Ahmed El-Desouky et al.   MATERIALS LETTERS

Power density optimization for micro thermoelectric generators

(2015) Marc T. Dunham et al.   ENERGY

Cost Scaling of a Real-World Exhaust Waste Heat Recovery Thermoelectric Generator: A Deeper Dive

(2015) Terry J. Hendricks et al.   JOURNAL OF ELECTRONIC MATERIALS

Multi-objective thermal analysis of a thermoelectric device: Influence of geometric features on device characteristics

(2014) Amin Ibrahim et al.   ENERGY

Design of Apparatus for Ni/Mg2Si and Ni/MnSi1.75 Contact Resistance Determination for Thermoelectric Legs

(2014) Yohann Thimont et al.   JOURNAL OF ELECTRONIC MATERIALS

Influence of electrical current variance and thermal resistances on optimum working conditions and geometry for thermoelectric energy harvesting

(2013) Miguel Gomez et al.   JOURNAL OF APPLIED PHYSICS

Preparation of Ring-Shaped Thermoelectric Legs from PbTe Powders for Tubular Thermoelectric Modules

(2013) Andreas Schmitz et al.   JOURNAL OF ELECTRONIC MATERIALS

Towards high efficiency segmented thermoelectric unicouples

(2013) Pham Hoang Ngan et al.   PHYSICA STATUS SOLIDI A-APPLICATIONS AND MATERIALS SCIENCE

The thermoelement as thermoelectric power generator: Effect of leg geometry on the efficiency and power generation

(2012) Ahmet Z. Sahin et al.   ENERGY CONVERSION AND MANAGEMENT

Thermoelectric Phenomena, Materials, and Applications

(2011) Terry M. Tritt   Annual Review of Materials Research

Cost-Efficiency Trade-off and the Design of Thermoelectric Power Generators

(2011) Kazuaki Yazawa et al.   ENVIRONMENTAL SCIENCE & TECHNOLOGY

Module Geometry and Contact Resistance of Thermoelectric Generators Analyzed by Multiphysics Simulation

(2010) D. Ebling et al.   JOURNAL OF ELECTRONIC MATERIALS

New and Old Concepts in Thermoelectric Materials

(2009) Joseph R. Sootsman et al.   ANGEWANDTE CHEMIE-INTERNATIONAL EDITION

New Physical Model for Thermoelectric Generators

(2009) Michael Freunek et al.   JOURNAL OF ELECTRONIC MATERIALS

Modeling the Building Blocks of a 10% Efficient Segmented Thermoelectric Power Generator

(2009) D. T. Crane et al.   JOURNAL OF ELECTRONIC MATERIALS