Effect of Combined Torsion and Tension on the Microstructure and Fracture Behavior of 316L Austenitic Stainless Steel

Fracture behavior of heterogeneous nanostructured 316L austenitic stainless steel with nanotwin bundles

(2018) L. Xiong et al.   ACTA MATERIALIA

Interface effects on the strength and ductility of bimodal nanostructured metals

(2018) X. Guo et al.   ACTA MECHANICA

Effects of grain refinement on the quasi-static compressive behavior of AISI 321 austenitic stainless steel: EBSD, TEM, and XRD studies

(2018) A.A. Tiamiyu et al.   INTERNATIONAL JOURNAL OF PLASTICITY

Microstructure evolution and enhanced mechanical properties in SUS316LN steel processed by high pressure torsion at room temperature

(2018) Shouwen Shi et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Effect of Severe Plastic Deformation on Microstructural and Mechanical Properties of Structural Steel IS2062

(2018) M. Nagaraj et al.   TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS

Effect of deformation-induced phase transformation on AISI 316 stainless steel corrosion resistance

(2017) Nicolae Solomon et al.   ENGINEERING FAILURE ANALYSIS

Limitations on the hardness increase in 316L stainless steel under dynamic plastic deformation

(2017) Ankur K. Agrawal et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Microstructure and Microtexture Evolution of Pure Titanium during Single Direction Torsion and Alternating Cyclic Torsion

(2017) Han Chen et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Intrinsic fracture toughness of bulk nanostructured Cu with nanoscale deformation twins

(2017) S.S. Luo et al.   SCRIPTA MATERIALIA

Microstructural evolution and phase transformation in twinning-induced plasticity steel induced by high-pressure torsion

(2016) X.H. An et al.   ACTA MATERIALIA

Experimental study on pure copper subjected to different severe plastic deformation modes

(2016) Jinghui Li et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Microstructure, mechanical and corrosion properties of friction stir welded high nitrogen nickel-free austenitic stainless steel

(2015) H.B. Li et al.   MATERIALS & DESIGN

Grain size dependence of the strength of metals: The Hall–Petch effect does not scale as the inverse square root of grain size

(2013) D.J. Dunstan et al.   INTERNATIONAL JOURNAL OF PLASTICITY

Influence of Strain Rate and Temperature on Tensile Deformation and Fracture Behavior of Type 316L(N) Austenitic Stainless Steel

(2013) B. K. Choudhary   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Strength and ductility of 316L austenitic stainless steel strengthened by nano-scale twin bundles

(2011) F.K. Yan et al.   ACTA MATERIALIA

Corrosion behaviour of nanocrystalline 304 stainless steel prepared by equal channel angular pressing

(2011) Z.J. Zheng et al.   CORROSION SCIENCE

Microstructure and nanohardness distribution in a polycrystalline Zn deformed by high strain rate impact

(2011) G. Dirras et al.   MATERIALS CHARACTERIZATION

Room-temperature equal channel angular extrusion of pure magnesium

(2010) Somjeet Biswas et al.   ACTA MATERIALIA

Effects of low-cycle fatigue on static mechanical properties, microstructures and fracture behavior of 304 stainless steel

(2010) Duyi Ye et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

High temperature microstructural evolution of 304L stainless steel as function of pre-strain and strain rate

(2010) Woei-Shyan Lee et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Deformation-induced martensitic transformation behavior in cold-rolled and cold-drawn type 316 stainless steels

(2009) Nobuo Nakada et al.   ACTA MATERIALIA

Experimental investigation on martensitic transformation and fracture morphologies of austenitic stainless steel

(2009) Arpan Das et al.   INTERNATIONAL JOURNAL OF PLASTICITY

Mechanical properties and rolling behaviors of nano-grained copper with embedded nano-twin bundles

(2008) Y. Zhang et al.   ACTA MATERIALIA

The significance of strain reversals during processing by high-pressure torsion

(2008) Megumi Kawasaki et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Influence of stress state and strain path on deformation induced martensitic transformations

(2007) E.S. Perdahcıoğlu et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING