Printability of 316 stainless steel

Heat and fluid flow in additive manufacturing—Part I: Modeling of powder bed fusion

(2018) T. Mukherjee et al.   COMPUTATIONAL MATERIALS SCIENCE

Residual stresses and distortion in additively manufactured compositionally graded and dissimilar joints

(2018) T. Mukherjee et al.   COMPUTATIONAL MATERIALS SCIENCE

Effect of Ni content on stainless steel fabricated by laser melting deposition

(2018) H. Zhang et al.   OPTICS AND LASER TECHNOLOGY

Additive manufacturing of metallic components – Process, structure and properties

(2018) T. DebRoy et al.   PROGRESS IN MATERIALS SCIENCE

Wire and arc additive manufacturing: a comparison between CMT and TopTIG processes applied to stainless steel

(2018) N. Rodriguez et al.   Welding in the World

Laser-Aided Directed Energy Deposition of Steel Powder over Flat Surfaces and Edges

(2018) Fabrizia Caiazzo et al.   Materials

The printability, microstructure, crystallographic features and microhardness of selective laser melted Inconel 718 thin wall

(2018) Huihui Yang et al.   MATERIALS & DESIGN

Fusion zone geometries, cooling rates and solidification parameters during wire arc additive manufacturing

(2018) W. Ou et al.   INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER

Mitigation of lack of fusion defects in powder bed fusion additive manufacturing

(2018) T. Mukherjee et al.   Journal of Manufacturing Processes

Dimensionless numbers in additive manufacturing

(2017) T. Mukherjee et al.   JOURNAL OF APPLIED PHYSICS

Microstructure and mechanical properties of the austenitic stainless steel 316L fabricated by gas metal arc additive manufacturing

(2017) Xiaohui Chen et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

A comparison on metallurgical behaviors of 316L stainless steel by selective laser melting and laser cladding deposition

(2017) Mingming Ma et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Influences of pulse laser parameters on properties of AISI316L stainless steel thin-walled part by laser material deposition

(2017) Xinlin Wang et al.   OPTICS AND LASER TECHNOLOGY

Morphologies, microstructures, and mechanical properties of samples produced using laser metal deposition with 316 L stainless steel wire

(2017) Xiang Xu et al.   OPTICS AND LASERS IN ENGINEERING

In-situ characterization of laser-powder interaction and cooling rates through high-speed imaging of powder bed fusion additive manufacturing

(2017) Umberto Scipioni Bertoli et al.   MATERIALS & DESIGN

Laser powder-bed fusion additive manufacturing: Physics of complex melt flow and formation mechanisms of pores, spatter, and denudation zones

(2016) Saad A. Khairallah et al.   ACTA MATERIALIA

A comparative study of additive manufacturing techniques: Residual stress and microstructural analysis of CLAD and WAAM printed Ti–6Al–4V components

(2016) Blanka A. Szost et al.   MATERIALS & DESIGN

Finite Element Simulation of Selective Laser Melting process considering Optical Penetration Depth of laser in powder bed

(2016) Ali Foroozmehr et al.   MATERIALS & DESIGN

Printability of alloys for additive manufacturing

(2016) T. Mukherjee et al.   Scientific Reports

Effects of process time interval and heat treatment on the mechanical and microstructural properties of direct laser deposited 316L stainless steel

(2015) Aref Yadollahi et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Heat transfer and material flow during laser assisted multi-layer additive manufacturing

(2014) V. Manvatkar et al.   JOURNAL OF APPLIED PHYSICS

Evaporation model for beam based additive manufacturing using free surface lattice Boltzmann methods

(2014) Alexander Klassen et al.   JOURNAL OF PHYSICS D-APPLIED PHYSICS

Spatial variation of melt pool geometry, peak temperature and solidification parameters during laser assisted additive manufacturing process

(2014) V. Manvatkar et al.   MATERIALS SCIENCE AND TECHNOLOGY

Characterization of stainless steel parts by Laser Metal Deposition Shaping

(2013) Kai Zhang et al.   MATERIALS & DESIGN

Densification behavior of gas and water atomized 316L stainless steel powder during selective laser melting

(2010) Ruidi Li et al.   APPLIED SURFACE SCIENCE

Residual stresses in LENS-deposited AISI 410 stainless steel plates

(2008) Liang Wang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING