Microscale shear specimens for evaluating the shear deformation in single-crystal and nanocrystalline Cu and at Cu–Si interfaces

Effects of interface shear strength during failure of semicoherent Metal–Metal nanolaminates: An example of accumulative roll-bonded Cu/Nb

(2018) I. Radchenko et al.   ACTA MATERIALIA

Measuring critical stress for shear failure of interfacial regions in coating/interlayer/substrate systems through a micro-pillar testing protocol

(2017) Yang Mu et al.   JOURNAL OF MATERIALS RESEARCH

Compact forced simple-shear sample for studying shear localization in materials

(2016) G.T. Gray et al.   ACTA MATERIALIA

Assessment of strain hardening in copper single crystals using in situ SEM microshear experiments

(2016) N. Wieczorek et al.   ACTA MATERIALIA

Microstructure evolution of pure copper during a single pass of simple shear extrusion (SSE): role of shear reversal

(2016) E. Bagherpour et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Micromechanical and in situ shear testing of Al–SiC nanolaminate composites in a transmission electron microscope (TEM)

(2015) C. Mayer et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Development of a high-resolution micro-torsion tester for measuring the shear modulus of metallic glass fibers

(2015) Y J Dai et al.   MEASUREMENT SCIENCE and TECHNOLOGY

Understanding size effects on the strength of single crystals through high-temperature micropillar compression

(2014) Rafael Soler et al.   ACTA MATERIALIA

A new experimental approach for evaluating the mechanical integrity of interfaces between hard coatings and substrates

(2014) Ke Chen et al.   MRS Communications

Buckling behaviors and adhesion energy of nanostructured Cu/X (X=Nb, Zr) multilayer films on a compliant substrate

(2013) K. Wu et al.   ACTA MATERIALIA

Microshear deformation of gold single crystals

(2013) J.-K. Heyer et al.   ACTA MATERIALIA

Plastic anisotropy and associated deformation mechanisms in nanotwinned metals

(2012) Zesheng You et al.   ACTA MATERIALIA

Toward a further understanding of size effects in the torsion of thin metal wires: An experimental and theoretical assessment

(2012) Dabiao Liu et al.   INTERNATIONAL JOURNAL OF PLASTICITY

Determination of the interfacial strength and fracture toughness of a-C:H coatings by in-situ microcantilever bending

(2012) J. Schaufler et al.   THIN SOLID FILMS

A new method to measure torsion moments on small-scaled specimens

(2011) M. Walter et al.   REVIEW OF SCIENTIFIC INSTRUMENTS

Tensile and compressive behavior of tungsten, molybdenum, tantalum and niobium at the nanoscale

(2010) Ju-Young Kim et al.   ACTA MATERIALIA

Detwinning mechanisms for growth twins in face-centered cubic metals

(2010) J. Wang et al.   ACTA MATERIALIA

Microstructure versus Size: Mechanical Properties of Electroplated Single Crystalline Cu Nanopillars

(2010) Andrew T. Jennings et al.   PHYSICAL REVIEW LETTERS

Influence of slip transmission on the migration of incoherent twin boundaries in epitaxial nanotwinned Cu

(2010) N. Li et al.   SCRIPTA MATERIALIA

The use of hat-shaped specimens to study the high strain rate shear behaviour of Ti–6Al–4V

(2009) J. Peirs et al.   INTERNATIONAL JOURNAL OF IMPACT ENGINEERING

Plastic flow stability of nanotwinned Cu foils

(2009) O. Anderoglu et al.   INTERNATIONAL JOURNAL OF PLASTICITY

Micro-compression testing: A critical discussion of experimental constraints

(2009) D. Kiener et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Interface fracture properties of thin films studied by using the micro-cantilever deflection technique

(2009) Kurt Matoy et al.   SURFACE & COATINGS TECHNOLOGY

Size-dependent mechanical properties of molybdenum nanopillars

(2008) Ju-Young Kim et al.   APPLIED PHYSICS LETTERS

Size effect on strength and strain hardening of small-scale [111] nickel compression pillars

(2008) C.P. Frick et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Using high-pressure torsion for metal processing: Fundamentals and applications

(2008) A ZHILYAEV et al.   PROGRESS IN MATERIALS SCIENCE

A search for evidence of strain gradient hardening in Au submicron pillars under uniaxial compression using synchrotron X-ray microdiffraction

(2007) A.S. Budiman et al.   ACTA MATERIALIA

Strain softening in nanocrystalline or ultrafine-grained metals: A mechanistic explanation

(2007) Feng Tang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING