Identification of cell-nucleation mechanism in foam injection molding with gas-counter pressure via mold visualization

Study of the bubble nucleation and growth mechanisms in high-pressure foam injection molding through in-situ visualization

(2016) Vahid Shaayegan et al.   EUROPEAN POLYMER JOURNAL

A new insight into foaming mechanisms in injection molding via a novel visualization mold

(2016) V. Shaayegan et al.   Express Polymer Letters

Heat transfer in microcellular polystyrene/multi-walled carbon nanotube nanocomposite foams

(2015) Pengjian Gong et al.   CARBON

Development of high void fraction polylactide composite foams using injection molding: Crystallization and foaming behaviors

(2015) A. Ameli et al.   CHEMICAL ENGINEERING JOURNAL

Nanocellular polymer foams as promising high performance thermal insulation materials

(2015) Shanqiu Liu et al.   EUROPEAN POLYMER JOURNAL

Experimental validation of the Knudsen effect in nanocellular polymeric foams

(2015) B. Notario et al.   POLYMER

Polymer nano-foams for insulating applications prepared from CO2 foaming

(2015) C. Forest et al.   PROGRESS IN POLYMER SCIENCE

A facile method to increase the charge storage capability of polymer nanocomposites

(2015) Aboutaleb Ameli et al.   Nano Energy

Superhydrophobic and Oleophilic Open-Cell Foams from Fibrillar Blends of Polypropylene and Polytetrafluoroethylene

(2014) Ali Rizvi et al.   ACS Applied Materials & Interfaces

Polypropylene/carbon nanotube nano/microcellular structures with high dielectric permittivity, low dielectric loss, and low percolation threshold

(2014) A. Ameli et al.   CARBON

Multiphase approach to coupled conduction–radiation heat transfer in reconstructed polymeric foams

(2014) Pavel Ferkl et al.   INTERNATIONAL JOURNAL OF THERMAL SCIENCES

Visualization of foaming phenomena in thermoplastic injection molding process

(2014) Ahmadzia Ahmadzai et al.   JOURNAL OF CELLULAR PLASTICS

Influence of relative low gas counter pressure on melt foaming behavior and surface quality of molded parts in microcellular injection molding process

(2014) Shuai Li et al.   JOURNAL OF CELLULAR PLASTICS

Design and development of novel bio-based functionally graded foams for enhanced acoustic capabilities

(2014) Shahrzad Ghaffari Mosanenzadeh et al.   JOURNAL OF MATERIALS SCIENCE

Research on formation mechanisms and control of external and inner bubble morphology in microcellular injection molding

(2014) Gui-long Wang et al.   POLYMER ENGINEERING AND SCIENCE

Development of high void fraction polylactide composite foams using injection molding: Mechanical and thermal insulation properties

(2013) A. Ameli et al.   COMPOSITES SCIENCE AND TECHNOLOGY

Mechanisms of nanoclay-enhanced plastic foaming processes: effects of nanoclay intercalation and exfoliation

(2013) Anson Wong et al.   JOURNAL OF NANOPARTICLE RESEARCH

Fundamental mechanisms of cell nucleation in polypropylene foaming with supercritical carbon dioxide—Effects of extensional stresses and crystals

(2013) Anson Wong et al.   JOURNAL OF SUPERCRITICAL FLUIDS

Open-cell cavity-integrated injection-molded acoustic polypropylene foams

(2013) D. Jahani et al.   MATERIALS & DESIGN

On thermal conductivity of micro- and nanocellular polymer foams

(2013) Sriharsha S. Sundarram et al.   POLYMER ENGINEERING AND SCIENCE

The effects of extensional stresses on the foamability of polystyrene–talc composites blown with carbon dioxide

(2012) Anson Wong et al.   CHEMICAL ENGINEERING SCIENCE

Structure and mechanical properties of polystyrene foams made through microcellular injection molding via control mechanisms of gas counter pressure and mold temperature

(2012) Shia-Chung Chen et al.   INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER

The effects of gas counter pressure and mold temperature variation on the surface quality and morphology of the microcellular polystyrene foams

(2012) Shia-Chung Chen et al.   JOURNAL OF APPLIED POLYMER SCIENCE

A visualization system for observing plastic foaming processes under shear stress

(2012) A. Wong et al.   POLYMER TESTING

A novel method for improving the surface quality of microcellular injection molded parts

(2011) Jungjoo Lee et al.   POLYMER

Microcellular and nanocellular solid-state polyetherimide (PEI) foams using sub-critical carbon dioxide II. Tensile and impact properties

(2011) Dustin Miller et al.   POLYMER

Novel foam injection molding technology using carbon dioxide-laden pellets

(2011) Jungjoo Lee et al.   POLYMER ENGINEERING AND SCIENCE

Visual observation and numerical studies of polymer foaming behavior of polypropylene/carbon dioxide system in a core-back injection molding process

(2011) Takeshi Ishikawa et al.   POLYMER ENGINEERING AND SCIENCE

Improving surface quality of microcellular injection molded parts through mold surface temperature manipulation with thin film insulation

(2010) Jungjoo Lee et al.   POLYMER ENGINEERING AND SCIENCE

Analysis of the Impact Properties of Structural Foams

(2009) Walter Michaeli et al.   JOURNAL OF CELLULAR PLASTICS

Strategies to Achieve a Uniform Cell Structure with a High Void Fraction in Advanced Structural Foam Molding

(2008) John W. S. Lee et al.   INDUSTRIAL & ENGINEERING CHEMISTRY RESEARCH

Using thermally insulated polymer film for mold temperature control to improve surface quality of microcellular injection molded parts

(2008) Hui-Li Chen et al.   INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER

Passive mold temperature control by a hybrid filming-microcellular injection molding processing

(2008) Shia-Chung Chen et al.   INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER

Advanced structural foam molding using a continuous polymer/gas melt flow stream

(2008) Xiang Xu et al.   JOURNAL OF APPLIED POLYMER SCIENCE

Effect of Processing Parameters on the Mechanical Properties of Injection Molded Thermoplastic Polyolefin (TPO) Cellular Foams

(2008) Steven Wong et al.   MACROMOLECULAR MATERIALS AND ENGINEERING