Impacts of Defocusing Amount and Molten Pool Boundaries on Mechanical Properties and Microstructure of Selective Laser Melted AlSi10Mg

Thermal behavior of the molten pool, microstructural evolution, and tribological performance during selective laser melting of TiC/316L stainless steel nanocomposites: Experimental and simulation methods

(2018) Bandar AlMangour et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Densification behavior, microstructural evolution, and mechanical properties of TiC/316L stainless steel nanocomposites fabricated by selective laser melting

(2018) Bandar AlMangour et al.   MATERIALS & DESIGN

Strain rate sensitivity and fracture mechanism of AlSi10Mg parts produced by Selective Laser Melting

(2017) I. Rosenthal et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Microstructure and strength of selectively laser melted AlSi10Mg

(2016) J. Wu et al.   ACTA MATERIALIA

Metallurgy of high-silicon steel parts produced using Selective Laser Melting

(2016) Michele Garibaldi et al.   ACTA MATERIALIA

Laser powder-bed fusion additive manufacturing: Physics of complex melt flow and formation mechanisms of pores, spatter, and denudation zones

(2016) Saad A. Khairallah et al.   ACTA MATERIALIA

Microstructure and phase formation in Al–20Si–5Fe–3Cu–1Mg synthesized by selective laser melting

(2016) Pan Ma et al.   JOURNAL OF ALLOYS AND COMPOUNDS

A selective laser melting and solution heat treatment refined Al–12Si alloy with a controllable ultrafine eutectic microstructure and 25% tensile ductility

(2015) X.P. Li et al.   ACTA MATERIALIA

Balling phenomena in selective laser melted tungsten

(2015) Xin Zhou et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Selective laser melting of AlSi10Mg alloy: Process optimisation and mechanical properties development

(2015) Noriko Read et al.   MATERIALS & DESIGN

On the role of thermal fluid dynamics into the evolution of porosity during selective laser melting

(2015) C. Panwisawas et al.   SCRIPTA MATERIALIA

Review of selective laser melting: Materials and applications

(2015) C. Y. Yap et al.   Applied Physics Reviews

On Optimization of Surface Roughness of Selective Laser Melted Stainless Steel Parts: A Statistical Study

(2014) K. Alrbaey et al.   JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE

Effect of molten pool boundaries on the mechanical properties of selective laser melting parts

(2014) Wen Shifeng et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Mesoscopic simulation model of selective laser melting of stainless steel powder

(2014) Saad A. Khairallah et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Defect generation and propagation mechanism during additive manufacturing by selective beam melting

(2014) A. Bauereiß et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Selective laser melting of Ti6Al4V alloy for biomedical applications: Temperature monitoring and microstructural evolution

(2013) I. Yadroitsev et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Microstructures and mechanical behavior of Inconel 718 fabricated by selective laser melting

(2012) K.N. Amato et al.   ACTA MATERIALIA

Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder

(2012) Lore Thijs et al.   ACTA MATERIALIA

Additive manufactured AlSi10Mg samples using Selective Laser Melting (SLM): Microstructure, high cycle fatigue, and fracture behavior

(2011) Erhard Brandl et al.   MATERIALS & DESIGN

Microstructure and mechanical behavior of Ti–6Al–4V produced by rapid-layer manufacturing, for biomedical applications

(2008) L.E. Murr et al.   Journal of the Mechanical Behavior of Biomedical Materials