Comparative study of hot-processing maps for 6061 aluminium alloy constructed from power constitutive equation and hyperbolic sine constitutive equation

Identification of optimal deforming parameters from a large range of strain, strain rate and temperature for 3Cr20Ni10W2 heat-resistant alloy

(2013) Guo-zheng Quan et al.   MATERIALS & DESIGN

Experimental study of hot deformation behavior in API X65 steel

(2013) M. Rakhshkhorshid et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Shear punch superplasticity in equal-channel angularly pressed Mg–12Li–1Zn alloy

(2013) M. Karami et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Investigation on hot deformation of 20Cr–25Ni superaustenitic stainless steel with starting columnar dendritic microstructure based on kinetic analysis and processing map

(2013) Y Han et al.   MATERIALS SCIENCE AND TECHNOLOGY

Study on hot deformation behaviour of 316LN austenitic stainless steel based on hot processing map

(2012) X G Liu et al.   MATERIALS SCIENCE AND TECHNOLOGY

High-temperature deformation behavior and processing map of 7050 aluminum alloy re]20101008

(2012) Jun-song Jin et al.   METALS AND MATERIALS INTERNATIONAL

Hot deformation behavior of a medium carbon microalloyed steel

(2011) H. Mirzadeh et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

The flow behavior modeling of cast A356 aluminum alloy at elevated temperatures considering the effect of strain

(2011) N. Haghdadi et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Influence of shallow and deep cryogenic treatment on the residual state of stress of 4140 steel

(2010) D. Senthilkumar et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

The workability evaluation of wrought AZ80 magnesium alloy in hot compression

(2010) Guo-Zheng Quan et al.   MATERIALS & DESIGN

On the characterization of recrystallized fraction using electron backscatter diffraction: A direct comparison to local hardness in an IF steel using nanoindentation

(2010) S. Dziaszyk et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Analysis of constitutive behaviours and processing map of 7020 aluminium alloy

(2010) Q.-J. Liu et al.   MATERIALS SCIENCE AND TECHNOLOGY

Plastic flow and microstructural evolution in Ti–6Al–2Zr–1Mo–1V alloys during hot deformation

(2010) X. J. Dong et al.   MATERIALS SCIENCE AND TECHNOLOGY

Microstructure modelling of hot deformation of Al–1%Mg alloy

(2009) J. Talamantes-Silva et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Influence of Lanthanum Ion-Implantation on Adhesive Property of Oxide Film Formed on Co-40Cr Alloy

(2008) Hui-ming JIN et al.   JOURNAL OF IRON AND STEEL RESEARCH INTERNATIONAL

Characterisation of dynamic recovery during hot deformation of spray formed Al–Li alloy (UL40) using processing map approach

(2008) G. Jagan Reddy et al.   MATERIALS SCIENCE AND TECHNOLOGY

Microstructure characterization of 7050 aluminum alloy during dynamic recrystallization and dynamic recovery

(2007) H.E. Hu et al.   MATERIALS CHARACTERIZATION

Deformation behavior and microstructure evolution of 7050 aluminum alloy during high temperature deformation

(2007) H.E. Hu et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING