4.8 Article

Design of a high-efficiency NH3-SCR reactor for stationary applications. A kinetic study of NH3 oxidation and NH3-SCR over V-based catalysts

Journal

APPLIED CATALYSIS B-ENVIRONMENTAL
Volume 179, Issue -, Pages 185-195

Publisher

ELSEVIER SCIENCE BV
DOI: 10.1016/j.apcatb.2015.05.017

Keywords

V2O5/WO3/TiO2 catalyst; NH3-SCR; NH3 oxidation; Indirect kinetic scheme; Kinetic modeling

Ask authors/readers for more resources

In this work, the kinetics of the NH3/NO/O-2 reacting system over V2O5-WO3/TiO2 catalysts was studied under conditions of NH3/NO ratio >= 1 and temperature up to 400 degrees C, where some ammonia oxidation is expected. NH3-SCR and NH3-oxidation tests were performed over powdered catalysts, at varying V-loads. Over a high V-load home-made catalyst, NO conversion passed through a maximum at increasing temperature, as commonly observed in SCR tests at the onset of ammonia oxidation; however, since the experiments were performed under excess ammonia, the high temperature decrease of NO conversion could not be associated with a lack of surface NH3. The experiments were interpreted as the evidence of an unselective NH3-oxidation route, giving rise to some NO production. NH3-oxidation tests, though, showed low selectivity to NO (which is in line with the current literature); however, a quantitative analysis of data showed that the observed product distribution is fully in line with an indirect-consecutive reaction scheme from NH3 to N-2, wherein NO is formed by NH3 oxidation and is then rapidly converted to N-2 via NH3-SCR. The kinetic investigation was extended to commercial catalysts with low and medium V-loads. NH3-SCR tests showed increasing trends of NO conversion with temperature within the range 250-400 degrees C, thus they did not show any clear evidence for NH3 oxidation. However, NH3-oxidation tests showed that the reaction was active above 350 degrees C; notably, over 95% selectivity to N-2 was observed. A quantitative analysis of the NH3-oxidation tests, based on the independent estimate of the intrinsic rate of NH3-SCR, showed that the observation of few ppm NO slip is fully in line with the assumption of a two-step kinetic scheme. A reaction path analysis shows that by neglecting the unselective nature of ammonia oxidation on V-catalysts the rate of this reaction is overestimated by a factor of 2. Preliminary evaluations suggest that the impact of NH3-oxidation on the integral performance of monolith reactors (operating at NH3/NO ratios close to 1) is non negligible, so that the correct identification of the reaction stoichiometry is crucial. (C) 2015 Elsevier B.V. All rights reserved.

Authors

I am an author on this paper
Click your name to claim this paper and add it to your profile.

Reviews

Primary Rating

4.8
Not enough ratings

Secondary Ratings

Novelty
-
Significance
-
Scientific rigor
-
Rate this paper

Recommended

Article Engineering, Civil

Influence of heat treatment on the formation of ultrafine-grained structure of Al-Li alloys processed by SPD

K. Rodak, A. Urbanczyk-Gucwa, M. Jablonska, J. Pawlicki, J. Mizera

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2018)

Article Thermodynamics

Thermal and structural analysis of high-tin bronze of chemical composition corresponding to the composition of the singing bowl

Magdalena Jablonska, Tomasz Maciag, Marian Nowak, Tomasz Rzychon, Monika Czerny, Karolina Kowalczyk

JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY (2019)

Article Engineering, Civil

Dual rolls equal channel extrusion as unconventional SPD process of the ultralow-carbon steel: finite element simulation, experimental investigations and microstructural analysis

M. B. Jablonska, K. Kowalczyk, M. Tkocz, T. Bulzak, I. Bednarczyk, S. Rusz

Summary: The paper presents results of FEM modelling, properties, and microstructure of ultralow-carbon ferritic steel after unconventional SPD process - DRECE. The DRECE process has a significant influence on the hardness distribution, fracture behavior, and microstructure evolution of the steel, leading to an increase in steel strength properties. Microstructural investigations show that the processed strips exhibit a dislocation cell microstructure and subgrains with low-angle grain boundaries, indicating a high level of grain refinement facilitated by this unconventional SPD method.

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2021)

Article Engineering, Civil

The effect of severe plastic deformation on the IF steel properties, evolution of structure and crystallographic texture after dual rolls equal channel extrusion deformation

M. B. Jablonska, K. Kowalczyk, M. Tkocz, R. Chulist, K. Rodak, I Bednarczyk, A. Cichanski

Summary: The mechanical properties of Ti-stabilized experimental IF steel strips processed by dual rolls equal channel extrusion (DRECE) were significantly improved, especially with an increase in the number of passes. The microstructural investigations revealed dislocation cell and grain structures with mostly low angle grain boundaries in the processed strips.

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2021)

Article Engineering, Civil

Effect of the number of passes on grain refinement, texture and properties of DC01 steel strip processed by the novel hybrid SPD method

K. Kowalczyk, M. B. Jablonska, M. Tkocz, R. Chulist, I Bednarczyk, T. Rzychon

Summary: Dual rolls equal channel extrusion (DRECE) is an unconventional severe plastic deformation process that can produce ultrafine-grained microstructures in metals and alloys. This study investigated the evolution of microstructure and texture in DC01 low-carbon steel strip after multiple passes of the DRECE process. The results showed the development of defected microstructures and weakened rolling texture, accompanied by an increase in microhardness.

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2022)

Review Engineering, Civil

Effect of the conversion of the plastic deformation work to heat on the behaviour of TWIP steels: a review

M. B. Jablonska

Summary: This study discusses the temperature change of TWIP steels during deformation, as a result of the conversion of plastic deformation work into heat. The methods of measuring or modeling these temperature changes are presented. The study highlights that TWIP steels generate higher heat during plastic deformation compared to conventional steels, due to their higher yield stresses and limit strains. This heat has a significant impact on the microstructure and properties of the deformed material. It can lead to changes in deformation mechanisms and affect workability and energy consumption.

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2023)

Article Engineering, Civil

Finite element analysis of material deformation behaviour during DRECE: the sheet metal SPD process

Marek Tkocz, Karolina Kowalczyk, Tomasz Bulzak, Magdalena B. Jablonska, Marek Hawryluk

Summary: The material deformation behavior during the DRECE process has been analyzed using FEM simulations. The simulations considered two different channel angles and two processing routes. The results showed significant strain and stress inhomogeneities across the strip thickness, which can be mitigated by choosing a specific processing route. The smaller channel die angle generates larger strain and higher strength of the strip, but reduces its ductility.

ARCHIVES OF CIVIL AND MECHANICAL ENGINEERING (2023)

Article Metallurgy & Metallurgical Engineering

INFLUENCE OF THE DRECE PROCESS OF SEVERE PLASTIC DEFORMATION ON THE MECHANICAL PROPERTIES OF THE ULTRA-LOW CARBON INTERSTITIAL FREE STEEL

K. Kowalczyk, M. Jablonska, S. Rusz, I. Bednarczyk

ARCHIVES OF METALLURGY AND MATERIALS (2018)

Article Metallurgy & Metallurgical Engineering

STUDY OF HOT DEFORMATION BEHAVIOR OF CuFe2 ALLOY

I Schindler, M. Sauer, P. Kawulok, K. Rodak, E. Hadasik, M. Barbara Jablonska, S. Rusz, V Sevcak

ARCHIVES OF METALLURGY AND MATERIALS (2019)

Article Chemistry, Physical

Advanced Heat Treatment of Pearlitic Rail Steel

Magdalena Jablonska, Filip Lewandowski, Bartosz Chmiela, Zbigniew Gronostajski

Summary: This study systematically investigates the heat treatments of 60E1 profile rails made of R350HT steel to meet the requirements of the EN 16273 standard. It also presents a concept of cooling rails on a semi-industrial station to achieve the desired properties. Dilatometric tests show that the optimal cooling rate is between 3°C/s and 6°C/s, meeting both the hardness distribution and microstructure requirements of the EN 16273 standard. Tests on the designed and built station reveal that the optimal pressure for the rail's microstructure and properties is 6.5 bar. The results confirm that the designed station can be used for controlled cooling of R350HT steel rails.

MATERIALS (2023)

Proceedings Paper Engineering, Manufacturing

Microstructural aspects of energy absorption of high manganese steels

M. B. Jablonska, K. Kowalczyk

6TH ICAFT-INTERNATIONAL CONFERENCE ON ACCURACY IN FORMING TECHNOLOGY 25TH SFU-SAXON CONFERENCE ON FORMING TECHNOLOGY6TH AUTOMETFORM-INTERNATIONAL LOWER SILESIA-SAXONY CONFERENCE ON ADVANCED METAL FORMING PROCESSES IN THE AUTOMOTIVE INDUSTRY (2019)

Proceedings Paper Materials Science, Multidisciplinary

THE EFFECT OF COLD DRAWING ON PROPERTIES AND MICROSTRUCTURE OF MANGANESE AUSTENITIC STEEL WIRE

Agnieszka Tomaszewska, Magdalena Jablonska, Marek Tkocz, Iwona Bednarczyk

28TH INTERNATIONAL CONFERENCE ON METALLURGY AND MATERIALS (METAL 2019) (2019)

Proceedings Paper Materials Science, Multidisciplinary

MICROSTRUCTURAL EVOLUTION AND MECHANICAL PROPERTIES OF ULTRA-LOW CARBON STEEL AFTER SEVERE PLASTIC DEFORMATION PROCESS

Magdalena Jablonska, Karolina Kowalczyk, Stanislav Rusz, Iwona Bednarczyk

28TH INTERNATIONAL CONFERENCE ON METALLURGY AND MATERIALS (METAL 2019) (2019)

Proceedings Paper Materials Science, Multidisciplinary

INVESTIGATION ON PROPERTIES OF STRUCTURAL STEELS DEFORMED AT DYNAMIC CONDITIONS

Magdalena Jablonska, Artur Cichanski, Marek Tkocz, Karolina Kowalczyk

28TH INTERNATIONAL CONFERENCE ON METALLURGY AND MATERIALS (METAL 2019) (2019)

Article Metallurgy & Metallurgical Engineering

THE EFFECT OF THE LENGTH OF THE DRAWING DIE SIZING PORTION ON THE ENERGY AND FORCE PARAMETERS OF THE MEDIUM-CARBON STEEL WIRE DRAWING PROCESS

M. Suliga, M. Jablonska, M. Hawryluk

ARCHIVES OF METALLURGY AND MATERIALS (2019)

Article Chemistry, Physical

Enhancing catalytic activity of zeolitic octahedral metal oxides through zinc incorporation for ethane oxidative dehydrogenation

Bolun Yu, Denan Li, Qianqian Zhu, Shufan Yao, Lifeng Zhang, Yanshuo Li, Zhenxin Zhang

Summary: This study successfully improved the catalytic activity of a zeolitic octahedral metal oxide by incorporating a single zinc species into its micropore. The zinc incorporation achieved a high ethane conversion rate and ethylene selectivity. Mechanism study showed that the isolated zinc site played a crucial role in activating oxygen and ethane, as well as stabilizing intermediates and transition states.

APPLIED CATALYSIS B-ENVIRONMENT AND ENERGY (2024)

Article Chemistry, Physical

Unveiling the synergistic effect between the metallic phase and bridging S species over MoS2 for highly efficient nitrogen fixation

Ruoqi Liu, Hao Fei, Jian Wang, Ting Guo, Fangyang Liu, Zhuangzhi Wu, Dezhi Wang

Summary: This work successfully synthesized a high-performing S-enriched MoS2 catalyst for electrocatalytic nitrogen reduction reaction (NRR), demonstrating high activity and selectivity. The synergistic effect of the 1T phase and bridging S22- species was shown to play a positive role in NRR performances, and DFT calculations revealed the mechanism behind the improved performance.

APPLIED CATALYSIS B-ENVIRONMENT AND ENERGY (2024)

Article Chemistry, Physical

Polymethylhydrosiloxane-modified gas-diffusion cathode for more efficient and durable H2O2 electrosynthesis in the context of water treatment

Pan Xia, Lele Zhao, Xi Chen, Zhihong Ye, Zhihong Zheng, Qiang He, Ignasi Sires

Summary: This study presents a modified gas-diffusion electrode (GDE) for highly efficient and stable H2O2 electrosynthesis by using trace polymethylhydrosiloxane (PMHS). DFT calculations provide an in-depth understanding of the roles of PMHS functional groups.

APPLIED CATALYSIS B-ENVIRONMENT AND ENERGY (2024)

Article Chemistry, Physical

Boron-doped rGO electrocatalyst for high effective generation of hydrogen peroxide: Mechanism and effect of oxygen-enriched air

Kwangchol Ri, Songsik Pak, Dunyu Sun, Qiang Zhong, Shaogui Yang, Songil Sin, Leliang Wu, Yue Sun, Hui Cao, Chunxiao Han, Chenmin Xu, Yazi Liu, Huan He, Shiyin Li, Cheng Sun

Summary: Different B-doped rGO catalysts were synthesized and their 2e- oxygen reduction reaction (ORR) performance was investigated. It was found that the 2e- ORR selectivity of B-doped rGO was influenced by the B content and oxygen mass transfer conditions. The synthesized catalyst exhibited high 2e- ORR selectivity and was capable of degrading organic pollutants continuously.

APPLIED CATALYSIS B-ENVIRONMENT AND ENERGY (2024)

Article Chemistry, Physical

Oxygen vacancies-modified S-scheme heterojunction of Bi-doped La2Ti2O7 and La-doped Bi4Ti3O12 to improve the NO gas removal avoiding NO2 product

Li Lv, Lin Lei, Qi-Wen Chen, Cheng-Li Yin, Huiqing Fan, Jian-Ping Zhou

Summary: Monoclinic phase La2Ti2O7 and orthorhombic phase Bi4Ti3O12 are widely used in photocatalysis due to their layered crystal structure. The electronic structures of these phases play a crucial role in their photocatalytic activity. Heat treatment in a nitrogen atmosphere introduces more oxygen vacancies into the S-scheme heterojunction, leading to enhanced NO removal efficiency.

APPLIED CATALYSIS B-ENVIRONMENT AND ENERGY (2024)

Article Chemistry, Physical

Understanding the synergistic effect of hydrated electron generation from argon plasma catalysis over Bi2O3/CeO2 for perfluorooctanoic acid dehalogenation: Mechanism and DFT study

Choe Earn Choong, Minhee Kim, Jun Sup Lim, Young June Hong, Geon Joon Lee, Keun Hwa Chae, In Wook Nah, Yeomin Yoon, Eun Ha Choi, Min Jang

Summary: In this study, the synergistic effect between argon-plasma-system (AP) and catalysts in promoting the production of reactive species for water remediation was investigated. By altering the oxygen vacancies concentration of CeO2/Bi2O3 catalyst, the production of hydrated electrons was stimulated for PFOA removal. The results showed that the built-in electric field in the Bi/Ce0.43 interface enhanced electron migration and eaq- generation, leading to improved PFOA removal efficiency.

APPLIED CATALYSIS B-ENVIRONMENT AND ENERGY (2024)

Article Chemistry, Physical

Ru clusters anchored on N-doped porous carbon-alumina matrix as efficient catalyst toward primary amines via reductive amination

Yushan Wu, Di Xu, Yanfei Xu, Xin Tian, Mingyue Ding

Summary: Efficient synthesis of primary amines from carbonyl compounds was achieved via reductive amination using Ru@NC-Al2O3 as a catalyst, exhibiting high activity and selectivity under mild conditions.

APPLIED CATALYSIS B-ENVIRONMENT AND ENERGY (2024)

Article Chemistry, Physical

Efficient 1O2 production from H2O2 over lattice distortion controlled spinel ferrites

Yilan Jiang, Peifang Wang, Tingyue Chen, Keyi Gao, Yiran Xiong, Yin Lu, Dionysios D. Dionysiou, Dawei Wang

Summary: By controlling the content of Co and Ni in Co1-xNixFe2O4, the production of O-1(2) from H2O2 can be regulated. NiFe2O4, with the lowest lattice distortion degree, can efficiently produce O-1(2) as the dominant reactive oxygen species. The system also exhibits significant resistance to water matrix interference.

APPLIED CATALYSIS B-ENVIRONMENT AND ENERGY (2024)

Article Chemistry, Physical

Tailoring the Mo-N/Mo-O configuration in MoO2/Mo2N heterostructure for ampere-level current density hydrogen production

Shuai Feng, Donglian Li, Hao Dong, Song Xie, Yaping Miao, Xuming Zhang, Biao Gao, Paul K. Chu, Xiang Peng

Summary: In this study, MoO2/Mo2N heterostructures were prepared by regulating the coordination of Mo atoms. The electrocatalyst exhibits high current density and excellent stability for hydrogen evolution reaction.

APPLIED CATALYSIS B-ENVIRONMENT AND ENERGY (2024)

Article Chemistry, Physical

Spin state-tailored tetrahedral and octahedral cobalt centers on millimetric Co-Al oxide catalysts as dual sites for synergistic peroxymonosulfate activation

Jia-Cheng E. Yang, Min -Ping Zhu, Daqin Guan, Baoling Yuan, Darren Delai Sun, Chenghua Sun, Ming-Lai Fu

Summary: This study successfully modulated the electron configuration and spin state of millimetric metal catalysts by adjusting the support curvature radius. The electronic structure-oriented spin catalysis was found to affect the degradation of pollutants, providing new insights for the design and production of highly active, reusable, and stable catalysts.

APPLIED CATALYSIS B-ENVIRONMENT AND ENERGY (2024)

Article Chemistry, Physical

Cu nanocrystals coupled with poly (heptazine imide) for synergistically enhanced photocatalytic CH3SH elimination: Facet engineering strengthened electron pump effect

Tao Zhong, Su Tang, Wenbin Huang, Wei Liu, Huinan Zhao, Lingling Hu, Shuanghong Tian, Chun He

Summary: In this study, a highly efficient photocatalyst for the elimination of CH3SH was developed by engineering different crystal facets and coupling them with PHI. Cu (111)/PHI exhibited the highest elimination efficiency and showed good stability and reusability. The enhanced surface electron pump effect and effective adsorption mechanisms were revealed through comprehensive characterizations and DFT calculations.

APPLIED CATALYSIS B-ENVIRONMENT AND ENERGY (2024)

Article Chemistry, Physical

NiSn intermetallic nanoparticles with geometrically isolated Ni sites for selective C-O cleavage of furfural

Feifei Yang, Tianyu Zhang, Jiankang Zhao, Wei Zhou, Nicole J. Libretto, Jeffrey T. Miller

Summary: A Ni3Sn intermetallic nano particle was found to have geometrically isolated Ni sites that could selectively cleave C-O bonds in biomass derivatives. This nano particle showed high activity and selectivity towards 2-methylfuran, unlike Ni nanoparticles that produced other unwanted products derived from the aromatic rings.

APPLIED CATALYSIS B-ENVIRONMENTAL (2024)

Article Chemistry, Physical

Nickel-facilitated in-situ surface reconstruction on spinel Co3O4 for enhanced electrochemical nitrate reduction to ammonia

Lulu Qiao, Di Liu, Anquan Zhu, Jinxian Feng, Pengfei Zhou, Chunfa Liu, Kar Wei Ng, Hui Pan

Summary: This study reveals that surface evolution plays a crucial role in enhancing the electrocatalytic performance of transition metal oxides for electrochemical nitrate reduction reaction (e-NO3RR). Incorporating nickel into Co3O4 can promote surface reconstruction and improve the adsorption of intermediates and reduce energy barriers, leading to enhanced catalytic performance. The reconstructed cobalt-nickel hydroxides (CoyNi1_y(OH)2) on the catalyst's surface serve as the active phase.

APPLIED CATALYSIS B-ENVIRONMENTAL (2024)

Article Chemistry, Physical

Unraveling the discriminative mechanisms for peroxy activation via atomically dispersed Fe-N5 sites for tunable water decontamination

Xinyu Song, Yang Shi, Zelin Wu, Bingkun Huang, Xinhao Wang, Heng Zhang, Peng Zhou, Wen Liu, Zhicheng Pan, Zhaokun Xiong, Bo Lai

Summary: This study explores the discriminative activities and mechanisms for activation of O-O bond in peroxy compounds via single-atom catalysts (SACs) with higher coordination numbers (M-N5). The atomic catalyst (Fe-SAC) with Fe-N5 as the active center was constructed, effectively activating peroxymonosulfate (PMS), peroxydisulfate (PDS), and hydrogen peroxide (H2O2). The study demonstrates the degradation efficiencies of acyclovir are related to the O-O bond length in different peroxy compounds, and reveals the discriminative mechanisms for activation of O-O bond in different Fenton-like systems.

APPLIED CATALYSIS B-ENVIRONMENTAL (2024)

Article Chemistry, Physical

Fe-Mn oxycarbide anchored on N-doped carbon for enhanced Fenton-like catalysis: Importance of high-valent metal-oxo species and singlet oxygen

Yangzhuo He, Hong Qin, Ziwei Wang, Han Wang, Yuan Zhu, Chengyun Zhou, Ying Zeng, Yicheng Li, Piao Xu, Guangming Zeng

Summary: A dual-metal-organic framework (MOF) assisted strategy was proposed to construct a magnetic Fe-Mn oxycarbide anchored on N-doped carbon for peroxymonosulfate (PMS) activation. The FeMn@NC-800 catalyst exhibited superior activity with almost 100% degradation of sulfamethazine (SMZ) in 30 minutes. The study provided insights for the rational design of high-performance heterogeneous catalysts and proposed a novel nonradical-based catalytic oxidation for environmental cleaning.

APPLIED CATALYSIS B-ENVIRONMENTAL (2024)