标题
Wear-Induced Changes in FSW Tool Pin Profile: Effect of Process Parameters
作者
关键词
-
出版物
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
Volume 49, Issue 6, Pages 2139-2150
出版商
Springer Nature
发表日期
2018-03-20
DOI
10.1007/s11661-018-4580-9
参考文献
相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。- A numerical methodology for predicting tool wear in Friction Stir Welding
- (2017) A.F. Hasan et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Degradation mechanisms of pcBN tool material during Friction Stir Welding of Ni-base alloy 625
- (2017) S. Hanke et al. WEAR
- Quantitative wear analysis of H13 steel tool during friction stir welding of Cu-0.8%Cr-0.1%Zr alloy
- (2017) Pankaj Sahlot et al. WEAR
- Effects of tool wear on friction stir welded joints of Ti–6Al–4V alloy
- (2016) A. R. Nasresfahani et al. MATERIALS SCIENCE AND TECHNOLOGY
- Calibration of dynamic tool–workpiece interface temperature measurement during friction stir welding
- (2016) Joshua Schmale et al. MEASUREMENT
- Tool Wear Characteristics and Effect on Microstructure in Ti-6Al-4V Friction Stir Welded Joints
- (2016) Ameth Fall et al. Metals
- Tool wear mechanisms in friction stir welding of Ti–6Al–4V alloy
- (2014) Jiye Wang et al. WEAR
- A Phenomenological Model for Tool Wear in Friction Stir Welding of Metal Matrix Composites
- (2013) Tracie J. Prater et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- Friction Stir Welding in HSLA-65 Steel: Part I. Influence of Weld Speed and Tool Material on Microstructural Development
- (2012) S. J. Barnes et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- Effect of Cryotreatment on Tool Wear Behaviour of Bohler K390 and AISI H13 Tool Steel During Friction Stir Welding of Copper
- (2012) K. Surekha et al. TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS
- Load bearing capacity of tool pin during friction stir welding
- (2011) A. Arora et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Tool Geometry for Friction Stir Welding—Optimum Shoulder Diameter
- (2011) M. Mehta et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- Friction Stir Welding of HSLA-65 Steel: Part II. The Influence of Weld Speed and Tool Material on the Residual Stress Distribution and Tool Wear
- (2011) A. Steuwer et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- Impact of tool wear on joint strength in friction stir spot welding of DP 980 steel
- (2011) M P Miles et al. SCIENCE AND TECHNOLOGY OF WELDING AND JOINING
- Review: friction stir welding tools
- (2011) R Rai et al. SCIENCE AND TECHNOLOGY OF WELDING AND JOINING
- Numerical simulation of a wear experiment
- (2011) J. Andersson et al. WEAR
- Back-of-the-envelope calculations in friction stir welding – Velocities, peak temperature, torque, and hardness
- (2010) A. Arora et al. ACTA MATERIALIA
- Optimization of friction stir welding parameters for dissimilar aluminum alloys
- (2010) M. Ghosh et al. MATERIALS & DESIGN
- Microstructure Evolution during Friction Stir Welding of Mill-Annealed Ti-6Al-4V
- (2010) A. L. Pilchak et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- Frictional wear evaluation of WC–Co alloy tool in friction stir spot welding of low carbon steel plates
- (2009) D.H. Choi et al. INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS
- Investigations on the Effects of the Tool Material, Geometry, and Tilt Angle on Friction Stir Welding of Pure Titanium
- (2009) K. Reshad Seighalani et al. JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
- Understanding the material flow path of friction stir welding process using unthreaded tools
- (2009) Olivier Lorrain et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Boride Formation Induced by pcBN Tool Wear in Friction-Stir-Welded Stainless Steels
- (2009) Seung Hwan C. Park et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- Microstructural and mechanical characterisation of friction stir welded 15-5PH steel
- (2009) T. Weinberger et al. SCIENCE AND TECHNOLOGY OF WELDING AND JOINING
- Wear analysis of hot forging dies
- (2009) Siamak Abachi et al. TRIBOLOGY INTERNATIONAL
- Friction stir welding of AZ31 magnesium alloy rolled sheets: Influence of processing parameters
- (2008) L. Commin et al. ACTA MATERIALIA
- Effect of microstructural evolution on mechanical properties of friction stir welded AA2009/SiCp composite
- (2008) A FENG et al. COMPOSITES SCIENCE AND TECHNOLOGY
- Friction Stir Processing Technology: A Review
- (2008) Z.Y. Ma METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- Recent advances in friction-stir welding – Process, weldment structure and properties
- (2008) R NANDAN et al. PROGRESS IN MATERIALS SCIENCE
- Torque, power requirement and stir zone geometry in friction stir welding through modeling and experiments
- (2008) A. Arora et al. SCRIPTA MATERIALIA
- Stir zone microstructure of commercial purity titanium friction stir welded using pcBN tool
- (2007) Yu Zhang et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
Find Funding. Review Successful Grants.
Explore over 25,000 new funding opportunities and over 6,000,000 successful grants.
ExploreFind the ideal target journal for your manuscript
Explore over 38,000 international journals covering a vast array of academic fields.
Search