Effect of extrusion parameters on microstructure and mechanical properties of Mg–6Zn–1Mn–0.2Gd alloy
出版年份 2023 全文链接
标题
Effect of extrusion parameters on microstructure and mechanical properties of Mg–6Zn–1Mn–0.2Gd alloy
作者
关键词
-
出版物
Emerging Materials Research
Volume 12, Issue 3, Pages 297-306
出版商
Thomas Telford Ltd.
发表日期
2023-07-24
DOI
10.1680/jemmr.22.00191
参考文献
相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。- A good balance between strength and ductility in Mg–Zn–Mn-Gd alloy
- (2021) Yang Zhao et al. INTERMETALLICS
- Effects of extrusion ratio and temperature on the microstructure and mechanical properties of Mg–Zn–Yb–Zr extrusion alloys
- (2021) Hao Lv et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- The role of recrystallization and grain growth in optimizing the sheet texture of magnesium alloys with calcium addition during annealing
- (2020) Fei Guo et al. Journal of Magnesium and Alloys
- Strengthening a dual-phase Mg–Li alloy by strain-induced phase transformation at room temperature
- (2020) Fei Guo et al. SCRIPTA MATERIALIA
- Effect of Gd addition on the age hardening response of Mg–6Zn-1Mn alloy
- (2020) Yang Zhao et al. Journal of Materials Research and Technology-JMR&T
- Improving ductility of a Mg alloy via non-basal slip induced by Ca addition
- (2019) Gaoming Zhu et al. INTERNATIONAL JOURNAL OF PLASTICITY
- Effects of Zn addition on the aging behavior and mechanical properties of Mg 8Al 2Sn wrought alloy
- (2019) Luyao Jiang et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Effects of extrusion ratio and temperature on the mechanical properties and microstructure of as-extruded Mg-Gd-Y-(Nd/Zn)-Zr alloys
- (2019) Zijian Yu et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Novel low-cost magnesium alloys with high yield strength and plasticity
- (2019) Peng Peng et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- The texture and its optimization in magnesium alloy
- (2019) Jialin Wu et al. JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY
- A micro-alloyed Mg-Sn-Y alloy with high ductility at room temperature
- (2018) Qinghang Wang et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Microstructure, texture evolution and tensile properties of extruded Mg-4.58Zn-2.6Gd-0.16Zr alloy
- (2018) Lei Xiao et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- The role of Al content on deformation behavior and related texture evolution during hot rolling of Mg-Al-Zn alloys
- (2017) Fei Guo et al. JOURNAL OF ALLOYS AND COMPOUNDS
- A review on the effect of rare-earth elements on texture evolution during processing of magnesium alloys
- (2016) A. Imandoust et al. JOURNAL OF MATERIALS SCIENCE
- Strain-induced selective grain growth in AZ31 Mg alloy sheet deformed by equal channel angular pressing
- (2016) J. Victoria-Hernández et al. MATERIALS CHARACTERIZATION
- Effect of ultra-slow extrusion speed on the microstructure and mechanical properties of Mg-4Zn-0.5Ca alloy
- (2016) Wei-jian Li et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Rare earth texture and improved ductility in a Mg-Zn-Gd alloy after high-speed extrusion
- (2016) M.G. Jiang et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- A review of dynamic recrystallization phenomena in metallic materials
- (2016) K. Huang et al. MATERIALS & DESIGN
- Influence of deformation rate on microstructure, texture and mechanical properties of indirect-extruded Mg–Zn–Ca alloy
- (2015) L.B. Tong et al. MATERIALS CHARACTERIZATION
- A new high-strength extruded Mg-8Al-4Sn-2Zn alloy
- (2015) Sung Hyuk Park et al. MATERIALS LETTERS
- Promotion of texture weakening in magnesium by alloying and thermomechanical processing: (I) alloying
- (2013) M. Sanjari et al. JOURNAL OF MATERIALS SCIENCE
- Influence of extrusion parameters on grain size and texture distributions of AZ31 alloy
- (2011) Weiqin Tang et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Role of Solute in the Texture Modification During Hot Deformation of Mg-Rare Earth Alloys
- (2011) Jason P. Hadorn et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- Distribution Characteristics of In-Grain Misorientation Axes in Cold-Rolled Commercially Pure Titanium and Their Correlation with Active Slip Modes
- (2010) Y. B. Chun et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- Bimodally grained microstructure development during hot extrusion of Mg–2.4 Zn–0.1 Ag–0.1 Ca–0.16 Zr (at.%) alloys
- (2009) K. Oh-ishi et al. ACTA MATERIALIA
- Particle effects on recrystallization in magnesium–manganese alloys: Particle-stimulated nucleation
- (2009) J.D. Robson et al. ACTA MATERIALIA
Add your recorded webinar
Do you already have a recorded webinar? Grow your audience and get more views by easily listing your recording on Peeref.
Upload NowBecome a Peeref-certified reviewer
The Peeref Institute provides free reviewer training that teaches the core competencies of the academic peer review process.
Get Started