Microstructure and mechanical properties of wire and arc additive manufactured thin wall with low-temperature transformation

Microstructure and Mechanical Properties of High-Strength, Low-Alloy Steel Thin-Wall Fabricated with Wire and Arc Additive Manufacturing

(2023) Kaijie Song et al.   Metals

Effect and mechanism of inter-layer ultrasonic impact strengthening on the anisotropy of low carbon steel components fabricated by wire and arc additive manufacturing

(2022) Laibo Sun et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Effect of induction heat treatment on residual stress distribution of components fabricated by wire arc additive manufacturing

(2022) Hongyao Shen et al.   Journal of Manufacturing Processes

Boron addition to AISI A213/P91 steel: Preliminary investigation on microstructural evolution and microhardness at simulated heat‐affected zone

(2022) A. Khajuria et al.   MATERIALWISSENSCHAFT UND WERKSTOFFTECHNIK

Effects of interlayer temperature on the microstructures of wire arc additive manufactured Al-Zn-Mg-Cu alloy: Insights into texture responses and dynamic precipitation behaviors

(2021) Bolun Dong et al.   Additive Manufacturing

Additive Manufacturing with Superduplex Stainless Steel Wire by CMT Process

(2020) Malin Lervåg et al.   Metals

Residual stresses in wire-arc additive manufacturing – Hierarchy of influential variables

(2020) Q. Wu et al.   Additive Manufacturing

Effects of ultrasonic peening treatment in three directions on grain refinement and anisotropy of cold metal transfer additive manufactured Ti-6Al-4V thin wall structure

(2020) Jian Gou et al.   Journal of Manufacturing Processes

Unravelling thermal history during additive manufacturing of martensitic stainless steel

(2020) Hobyung Chae et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Wire-arc additive manufacturing and post-heat treatment optimization on microstructure and mechanical properties of Grade 91 steel

(2020) Kun Li et al.   Additive Manufacturing

Investigation on thermal stress evolution induced by wire and arc additive manufacturing for circular thin-walled parts

(2019) Rong Li et al.   Journal of Manufacturing Processes

Effect of Boron Addition on Creep Strain during Impression Creep of P91 Steel

(2019) Akhil Khajuria et al.   JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE

Wire and arc additive manufacturing of HSLA steel: Effect of thermal cycles on microstructure and mechanical properties

(2019) Tiago A. Rodrigues et al.   Additive Manufacturing

Evidence of austenite memory in PH 15-5 and assessment of its formation mechanism

(2019) Dominik Brandl et al.   MATERIALS & DESIGN

Microstructure evolution during austenite reversion in Fe-Ni martensitic alloys

(2018) H. Shirazi et al.   ACTA MATERIALIA

Sensitivity of Ti-6Al-4V components to oxidation during out of chamber Wire + Arc Additive Manufacturing

(2018) M.J. Bermingham et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Formation and improvement of surface waviness for additive manufacturing 5A06 aluminium alloy component with GTAW system

(2018) Haibin Geng et al.   RAPID PROTOTYPING JOURNAL

A spatial periodicity of microstructural evolution and anti-indentation properties of wire-arc additive manufacturing 2Cr13 thin-wall part

(2018) Jinguo Ge et al.   MATERIALS & DESIGN

Phase transformations and numerical modelling in simulated HAZ of nanostructured P91B steel for high temperature applications

(2018) Modassir Akhtar et al.   Applied Nanoscience

Residual Stress, Mechanical Properties, and Grain Morphology of Ti-6Al-4V Alloy Produced by Ultrasonic Impact Treatment Assisted Wire and Arc Additive Manufacturing

(2018) Yichong Yang et al.   Metals

Comparison of two types of low-transformation-temperature weld metals based on solidification mode

(2017) Zhong-Yuan Feng et al.   SCIENCE AND TECHNOLOGY OF WELDING AND JOINING

Influence of plastic deformation heterogeneity on development of geometrically necessary dislocation density in dual phase steel

(2016) Amrita Kundu et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Residual stress of as-deposited and rolled wire+arc additive manufacturing Ti–6Al–4V components

(2016) F. Martina et al.   MATERIALS SCIENCE AND TECHNOLOGY

Effect of Prior Austenite Grain Size Refinement by Thermal Cycling on the Microstructural Features of As-Quenched Lath Martensite

(2016) Javier Hidalgo et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Development of a laminar flow local shielding device for wire + arc additive manufacture

(2015) J. Ding et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Transition from Diffusive to Displacive Austenite Reversion in Low-Alloy Steel

(2014) Nobuo Nakada et al.   ISIJ INTERNATIONAL

Martensite transformation kinetics in 9Cr–1.7W–0.4Mo–Co ferritic steel

(2014) Qiuzhi Gao et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Residual stress engineering by low transformation temperature alloys—state of the art and recent developments

(2014) Arne Kromm et al.   Welding in the World

Effect of Prior Austenite Grain Size on the Morphology and Mechanical Properties of Martensite in Medium Carbon Steel

(2012) Y. Prawoto et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

Neutron diffraction in situ monitoring of the dislocation density during martensitic transformation in a stainless steel

(2012) F. Christien et al.   SCRIPTA MATERIALIA

In situ study of structural integrity of low transformation temperature (LTT)-welds

(2011) J. Altenkirch et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

In-Situ Observations of Martensitic Transformation in Blast-Resistant Steel

(2011) Xinghua Yu et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Austenite grain size and the martensite-start temperature

(2008) H YANG et al.   SCRIPTA MATERIALIA