Strength enhancement and modulus modulation in auxetic meta-biomaterials produced by selective laser melting
出版年份 2022 全文链接
标题
Strength enhancement and modulus modulation in auxetic meta-biomaterials produced by selective laser melting
作者
关键词
-
出版物
Acta Biomaterialia
Volume -, Issue -, Pages -
出版商
Elsevier BV
发表日期
2022-09-24
DOI
10.1016/j.actbio.2022.09.045
参考文献
相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。- Fatigue performance of auxetic meta-biomaterials
- (2021) H.M.A. Kolken et al. Acta Biomaterialia
- On the application of additive manufacturing methods for auxetic structures: a review
- (2021) Athul Joseph et al. Advances in Manufacturing
- Mechanisms of fatigue crack initiation and propagation in auxetic meta-biomaterials
- (2021) H.M.A. Kolken et al. Acta Biomaterialia
- Additive manufacturing of metallic lattice structures: Unconstrained design, accurate fabrication, fascinated performances, and challenges
- (2021) Liang-Yu Chen et al. MATERIALS SCIENCE & ENGINEERING R-REPORTS
- Three-dimensional-printed individualized porous implants: A new “implant-bone” interface fusion concept for large bone defect treatment
- (2021) Teng Zhang et al. Bioactive Materials
- Mechanical performance of auxetic meta-biomaterials
- (2020) H.M.A. Kolken et al. Journal of the Mechanical Behavior of Biomedical Materials
- Mechanical properties and energy absorption capabilities of functionally graded lattice structures: Experiments and simulations
- (2020) Long Bai et al. INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES
- Study on blast resistance of a composite sandwich panel with isotropic foam core with negative Poisson's ratio
- (2020) Weitao Lv et al. INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES
- Design and performance evaluation of additively manufactured composite lattice structures of commercially pure Ti (CP–Ti)
- (2020) Wei Xu et al. Bioactive Materials
- A Review on Biomedical Titanium Alloys: Recent Progress and Prospect
- (2019) Lai‐Chang Zhang et al. ADVANCED ENGINEERING MATERIALS
- Mechanical properties tailoring of topology optimized and selective laser melting fabricated Ti6Al4V lattice structure
- (2019) Yangli Xu et al. Journal of the Mechanical Behavior of Biomedical Materials
- Compression-compression fatigue behaviour of Gyroid-type Triply Periodic Minimal Surface porous structures fabricated by Selective Laser Melting
- (2019) Lei Yang et al. ACTA MATERIALIA
- Shear resistance of an auxetic chiral mechanical metamaterial
- (2019) Shengguang Jin et al. INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES
- An investigation into the effect of gradients on the manufacturing fidelity of triply periodic minimal surface structures with graded density fabricated by selective laser melting
- (2019) Lei Yang et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Optimisation of process parameters to address fundamental challenges during selective laser melting of Ti-6Al-4V: A review
- (2018) H. Shipley et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- Characterisation and constitutive model of tensile properties of selective laser melted Ti-6Al-4V struts for microlattice structures
- (2018) Zhiyong Wang et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Mechanical metamaterials associated with stiffness, rigidity and compressibility: A brief review
- (2018) Xianglong Yu et al. PROGRESS IN MATERIALS SCIENCE
- Auxetic metamaterials and structures: a review
- (2018) Xin Ren et al. Smart Materials and Structures
- Rationally designed meta-implants: a combination of auxetic and conventional meta-biomaterials
- (2018) Helena M. A. Kolken et al. Materials Horizons
- Effect of pore geometry on the fatigue properties and cell affinity of porous titanium scaffolds fabricated by selective laser melting
- (2018) Danlei Zhao et al. Journal of the Mechanical Behavior of Biomedical Materials
- Dynamic indentation of auxetic and non-auxetic honeycombs under large deformation
- (2018) L.L. Hu et al. COMPOSITE STRUCTURES
- Manufacturability of AlSi10Mg overhang structures fabricated by laser powder bed fusion
- (2018) Quanquan Han et al. MATERIALS & DESIGN
- Mechanical performance of additively manufactured meta-biomaterials
- (2018) Amir A. Zadpoor Acta Biomaterialia
- Structural optimization of re-entrant negative Poisson's ratio structure fabricated by selective laser melting
- (2017) Jiapeng Xiong et al. MATERIALS & DESIGN
- High-strength porous biomaterials for bone replacement: A strategy to assess the interplay between cell morphology, mechanical properties, bone ingrowth and manufacturing constraints
- (2016) Sajad Arabnejad et al. Acta Biomaterialia
- The development of TiNi-based negative Poisson's ratio structure using selective laser melting
- (2016) Sheng Li et al. ACTA MATERIALIA
- Topological design and additive manufacturing of porous metals for bone scaffolds and orthopaedic implants: A review
- (2016) Xiaojian Wang et al. BIOMATERIALS
- Mechanical properties of 3D re-entrant honeycomb auxetic structures realized via additive manufacturing
- (2015) Li Yang et al. INTERNATIONAL JOURNAL OF SOLIDS AND STRUCTURES
- Prevalence of Total Hip and Knee Replacement in the United States
- (2015) Hilal Maradit Kremers et al. JOURNAL OF BONE AND JOINT SURGERY-AMERICAN VOLUME
- Failure mechanisms of additively manufactured porous biomaterials: Effects of porosity and type of unit cell
- (2015) J. Kadkhodapour et al. Journal of the Mechanical Behavior of Biomedical Materials
- Vibration transmissibility and damping behaviour for auxetic and conventional foams under linear and nonlinear regimes
- (2013) Matteo Bianchi et al. Smart Materials and Structures
- The effect of pore geometry on the in vitro biological behavior of human periosteum-derived cells seeded on selective laser-melted Ti6Al4V bone scaffolds
- (2012) S. Van Bael et al. Acta Biomaterialia
- Mechanical evaluation of porous titanium (Ti6Al4V) structures with electron beam melting (EBM)
- (2009) Jayanthi Parthasarathy et al. Journal of the Mechanical Behavior of Biomedical Materials
- Cellular Ti–6Al–4V structures with interconnected macro porosity for bone implants fabricated by selective electron beam melting
- (2008) Peter Heinl et al. Acta Biomaterialia
- The effect of geometry on three-dimensional tissue growth
- (2008) M. Rumpler et al. Journal of the Royal Society Interface
- Mathematical relationships between bone density and mechanical properties: A literature review
- (2007) Benedikt Helgason et al. CLINICAL BIOMECHANICS
Discover Peeref hubs
Discuss science. Find collaborators. Network.
Join a conversationAsk a Question. Answer a Question.
Quickly pose questions to the entire community. Debate answers and get clarity on the most important issues facing researchers.
Get Started