On the influence of build orientation on properties of friction stir welded Al–Si10Mg parts produced by selective laser melting

Effect of Friction Stir Processing on Microstructural, Mechanical, and Corrosion Properties of Al-Si12 Additive Manufactured Components

(2020) Ghazal Moeini et al.   Metals

Premature failure of an additively manufactured material

(2020) Zhi Wang et al.   NPG Asia Materials

Very-high-cycle fatigue behavior of AlSi10Mg manufactured by selective laser melting: Effect of build orientation and mean stress

(2020) Guian Qian et al.   INTERNATIONAL JOURNAL OF FATIGUE

Cyclic deformation response of ultra-fine grained titanium at elevated temperatures

(2019) S.V. Sajadifar et al.   INTERNATIONAL JOURNAL OF FATIGUE

Microstructure, porosity and mechanical properties of selective laser melted AlSi10Mg

(2019) Jing CHEN et al.   Chinese Journal of Aeronautics

On the low-cycle fatigue behavior of friction stir welded Al–Si12 parts produced by selective laser melting

(2019) G. Moeini et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Comparative study of performance comparison of AlSi10Mg alloy prepared by selective laser melting and casting

(2019) Bo Song et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

Electron beam welding of laser additive manufacturing Ti–6.5Al–3.5Mo–1.5Zr–0.3Si titanium alloy thick plate

(2018) Xiaohui Chen et al.   VACUUM

Low cycle fatigue behavior of AlSi10Mg(Cu) alloy at high temperature

(2018) Cheng Cai et al.   MATERIALS CHARACTERIZATION

Analysis of Weak Zones in Friction Stir Welded Magnesium Alloys from the Viewpoint of Local Texture: A Short Review

(2018) Dejia Liu et al.   Metals

Effects of building orientation and heat treatment on fatigue behavior of selective laser melted 17-4 PH stainless steel

(2017) Aref Yadollahi et al.   INTERNATIONAL JOURNAL OF FATIGUE

Direction and location dependency of selective laser melted AlSi10Mg specimens

(2017) Leonhard Hitzler et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Strength and strain hardening of a selective laser melted AlSi10Mg alloy

(2017) B. Chen et al.   SCRIPTA MATERIALIA

Simultaneous enhancements of strength and toughness in an Al-12Si alloy synthesized using selective laser melting

(2016) Jyoti Suryawanshi et al.   ACTA MATERIALIA

Effect of heat treatment on AlSi10Mg alloy fabricated by selective laser melting: Microstructure evolution, mechanical properties and fracture mechanism

(2016) Wei Li et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Aging kinetics of friction stir welded Al-Cu-Li-Mg-Ag and Al-Cu-Li-Mg alloys

(2016) Harpreet Sidhar et al.   MATERIALS & DESIGN

Fatigue behavior of friction stir welded Al–Mg–Sc alloy

(2015) Michael Besel et al.   INTERNATIONAL JOURNAL OF FATIGUE

Friction welding of Al–12Si parts produced by selective laser melting

(2014) K.G. Prashanth et al.   MATERIALS & DESIGN

Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder

(2012) Lore Thijs et al.   ACTA MATERIALIA

On the low-cycle fatigue response of pre-strained austenitic Fe61Mn24Ni6.5Cr8.5 alloy showing TWIP effect

(2012) H.-G. Lambers et al.   INTERNATIONAL JOURNAL OF FATIGUE

Additive manufactured AlSi10Mg samples using Selective Laser Melting (SLM): Microstructure, high cycle fatigue, and fracture behavior

(2011) Erhard Brandl et al.   MATERIALS & DESIGN

Effect of trace La addition on the microstructures and mechanical properties of A356 (Al–7Si–0.35Mg) aluminum alloys

(2009) Yu-Chou Tsai et al.   JOURNAL OF ALLOYS AND COMPOUNDS