Efficient optimization methodology for laser powder bed fusion parameters to manufacture dense and mechanically sound parts validated on AlSi12 alloy
出版年份 2020 全文链接
标题
Efficient optimization methodology for laser powder bed fusion parameters to manufacture dense and mechanically sound parts validated on AlSi12 alloy
作者
关键词
Laser powder bed fusion (L-PBF), Selective laser melting (SLM), Parameters optimization, Methodology, Design of experiments (DOE), Aluminum alloy
出版物
MATERIALS & DESIGN
Volume 199, Issue -, Pages 109433
出版商
Elsevier BV
发表日期
2020-12-25
DOI
10.1016/j.matdes.2020.109433
参考文献
相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。- Multi-objective accelerated process optimization of mechanical properties in laser-based additive manufacturing: Case study on Selective Laser Melting (SLM) Ti-6Al-4V
- (2019) Amir M. Aboutaleb et al. Journal of Manufacturing Processes
- High-density tungsten fabricated by selective laser melting: Densification, microstructure, mechanical and thermal performance
- (2019) Shifeng Wen et al. OPTICS AND LASER TECHNOLOGY
- Ductilisation and fatigue life enhancement of selective laser melted AlSi10Mg by friction stir processing
- (2019) Juan Guillermo Santos Macías et al. SCRIPTA MATERIALIA
- Optimization and comparison of porosity rate measurement methods of Selective Laser Melted metallic parts
- (2019) Thibaut de Terris et al. Additive Manufacturing
- On the study of keyhole-mode melting in selective laser melting process
- (2019) K.Q. Le et al. INTERNATIONAL JOURNAL OF THERMAL SCIENCES
- A time-saving and cost-effective method to process alloys by Laser Powder Bed Fusion
- (2019) Federico Bosio et al. MATERIALS & DESIGN
- Analysis of processing parameters and characteristics of selective laser melted high strength Al-Cu-Mg alloys: From single tracks to cubic samples
- (2018) Xiaojia Nie et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Single scan track analyses on aluminium based powders
- (2018) Alberta Aversa et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Porosity formation mechanisms and fatigue response in Al-Si-Mg alloys made by selective laser melting
- (2018) Kun V. Yang et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- A Computational Study on Porosity Evolution in Parts Produced by Selective Laser Melting
- (2018) J. L. Tan et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- Influence of scan strategy and molten pool configuration on microstructures and tensile properties of selective laser melting additive manufactured aluminum based parts
- (2018) Donghua Dai et al. OPTICS AND LASER TECHNOLOGY
- Optimization of SLM process parameters for Ti6Al4V medical implants
- (2018) Mahmoud Elsayed et al. RAPID PROTOTYPING JOURNAL
- Formation of scanning tracks during Selective Laser Melting (SLM) of pure tungsten powder: Morphology, geometric features and forming mechanisms
- (2018) Meng Guo et al. INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS
- Laser directed energy deposition of water-atomized iron powder: Process optimization and microstructure of single-tracks
- (2018) Mohammad Ansari et al. OPTICS AND LASER TECHNOLOGY
- Effects of building orientation and heat treatment on fatigue behavior of selective laser melted 17-4 PH stainless steel
- (2017) Aref Yadollahi et al. INTERNATIONAL JOURNAL OF FATIGUE
- Additive manufacturing of fatigue resistant materials: Challenges and opportunities
- (2017) Aref Yadollahi et al. INTERNATIONAL JOURNAL OF FATIGUE
- Microstructure and strength analysis of eutectic Al-Si alloy in-situ manufactured using selective laser melting from elemental powder mixture
- (2017) Nan Kang et al. JOURNAL OF ALLOYS AND COMPOUNDS
- Simultaneous enhancements of strength and toughness in an Al-12Si alloy synthesized using selective laser melting
- (2016) Jyoti Suryawanshi et al. ACTA MATERIALIA
- Influence of hatch spacing on heat and mass transfer, thermodynamics and laser processability during additive manufacturing of Inconel 718 alloy
- (2016) Mujian Xia et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- Quantification and characterisation of porosity in selectively laser melted Al–Si10–Mg using X-ray computed tomography
- (2016) I. Maskery et al. MATERIALS CHARACTERIZATION
- Microstructure and wear behavior of in-situ hypereutectic Al–high Si alloys produced by selective laser melting
- (2016) Nan Kang et al. MATERIALS & DESIGN
- On the role of melt flow into the surface structure and porosity development during selective laser melting
- (2015) Chunlei Qiu et al. ACTA MATERIALIA
- Influence of process-induced microstructure and imperfections on mechanical properties of AlSi12 processed by selective laser melting
- (2015) Shafaqat Siddique et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Selective laser melting of AlSi10Mg alloy: Process optimisation and mechanical properties development
- (2015) Noriko Read et al. MATERIALS & DESIGN
- Effects of process time interval and heat treatment on the mechanical and microstructural properties of direct laser deposited 316L stainless steel
- (2015) Aref Yadollahi et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Optimisation of selective laser melting for a high temperature Ni-superalloy
- (2015) Luke N. Carter et al. RAPID PROTOTYPING JOURNAL
- Processing AlSi10Mg by selective laser melting: parameter optimisation and material characterisation
- (2014) K. Kempen et al. MATERIALS SCIENCE AND TECHNOLOGY
- Fine-structured aluminium products with controllable texture by selective laser melting of pre-alloyed AlSi10Mg powder
- (2012) Lore Thijs et al. ACTA MATERIALIA
- Property evaluation of 304L stainless steel fabricated by selective laser melting
- (2012) K. Abd‐Elghany et al. RAPID PROTOTYPING JOURNAL
- Balling behavior of stainless steel and nickel powder during selective laser melting process
- (2011) Ruidi Li et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Single track formation in selective laser melting of metal powders
- (2010) I. Yadroitsev et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Balling phenomena in direct laser sintering of stainless steel powder: Metallurgical mechanisms and control methods
- (2009) Dongdong Gu et al. MATERIALS & DESIGN
Discover Peeref hubs
Discuss science. Find collaborators. Network.
Join a conversationCreate your own webinar
Interested in hosting your own webinar? Check the schedule and propose your idea to the Peeref Content Team.
Create Now