Elevated temperature mechanical properties of TiCN reinforced AlSi10Mg fabricated by laser powder bed fusion additive manufacturing
出版年份 2021 全文链接
标题
Elevated temperature mechanical properties of TiCN reinforced AlSi10Mg fabricated by laser powder bed fusion additive manufacturing
作者
关键词
Laser powder bed fusion, Additive manufacturing, Aluminum metal matrix composites, Elevated temperature mechanical properties, Microstructure
出版物
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
Volume -, Issue -, Pages 141025
出版商
Elsevier BV
发表日期
2021-03-11
DOI
10.1016/j.msea.2021.141025
参考文献
相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。- Microstructure, solidification behavior and mechanical properties of Al-Si-Mg-Ti/TiC fabricated by selective laser melting
- (2020) Li Xinwei et al. Additive Manufacturing
- Selective laser melting of TiN nanoparticle-reinforced AlSi10Mg composite: Microstructural, interfacial, and mechanical properties
- (2020) C. Gao et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Simultaneous enhancement of strength, ductility, and hardness of TiN/AlSi10Mg nanocomposites via selective laser melting
- (2020) C. Gao et al. Additive Manufacturing
- Machine-learning assisted laser powder bed fusion process optimization for AlSi10Mg: New microstructure description indices and fracture mechanisms
- (2020) Qian Liu et al. ACTA MATERIALIA
- Effect of TiB2 particles on microstructure and crystallographic texture of Al-12Si fabricated by selective laser melting
- (2019) L. Xi et al. JOURNAL OF ALLOYS AND COMPOUNDS
- Influence of processing parameters on selective laser melted SiCp/AlSi10Mg composites: Densification, microstructure and mechanical properties
- (2019) Gang Xue et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Effect of Zr on the high cycle fatigue and mechanical properties of Al–Si–Cu–Mg alloys at elevated temperatures
- (2019) Guangyu Liu et al. JOURNAL OF ALLOYS AND COMPOUNDS
- Enhanced strength and ductility at room and elevated temperatures of Al-Cu alloy matrix composites reinforced with bimodal-sized TiC p compared with monomodal–sized TiC p
- (2018) Wei-Si Tian et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Selective laser melting of nano-TiN modified AlSi10Mg composite powder with low laser reflectivity
- (2018) Chaofeng Gao et al. MATERIALS LETTERS
- Micromechanisms of deformation in dual phase steels at high strain rates
- (2017) Anindya Das et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- The role of transition metal additions on the ambient and elevated temperature properties of Al-Si alloys
- (2017) Mohammadreza Zamani et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Novel Composite Powders with Uniform TiB2 Nano-Particle Distribution for 3D Printing
- (2017) Mengxing Chen et al. Applied Sciences-Basel
- Nanoparticle-inhibited growth of primary aluminum in Al–10Si alloys
- (2016) K. Wang et al. ACTA MATERIALIA
- On the mechanical behavior of cold deformed aluminum 7075 alloy at elevated temperatures
- (2016) K. Shojaei et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Microstructure and mechanical properties of hypoeutectic Al–Si composite reinforced with TiCN nanoparticles
- (2016) K. Wang et al. MATERIALS & DESIGN
- A selective laser melting and solution heat treatment refined Al–12Si alloy with a controllable ultrafine eutectic microstructure and 25% tensile ductility
- (2015) X.P. Li et al. ACTA MATERIALIA
- High-temperature mechanical properties and fracture mechanisms of Al–Si piston alloy reinforced with in situ TiB 2 particles
- (2015) Gang Han et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Rapid fabrication of Al-based bulk-form nanocomposites with novel reinforcement and enhanced performance by selective laser melting
- (2015) Dongdong Gu et al. SCRIPTA MATERIALIA
- High temperature tensile deformation behavior and failure mechanisms of an Al–Si–Cu–Mg cast alloy — The microstructural scale effect
- (2015) Mohammadreza Zamani et al. MATERIALS & DESIGN
- Effect of microstructure and overaging on the tensile behavior at room and elevated temperature of C355-T6 cast aluminum alloy
- (2015) Lorella Ceschini et al. MATERIALS & DESIGN
- Hot tensile deformation behaviors and constitutive model of an Al–Zn–Mg–Cu alloy
- (2014) Mi Zhou et al. MATERIALS & DESIGN
- Fabrication of nano-TiCp reinforced Inconel 625 composite coatings by partial dissolution of micro-TiCp through laser cladding energy input control
- (2014) Dafa Jiang et al. SURFACE & COATINGS TECHNOLOGY
- Dry Sliding Wear Behavior of Al2O3/SiC Particle Reinforced Aluminium Based MMCs Fabricated by Stir Casting Method
- (2013) N. Altınkok et al. ACTA PHYSICA POLONICA A
- Workability characteristics and mechanical behavior modeling of severely deformed pure titanium at high temperatures
- (2013) Seyed Vahid Sajadifar et al. MATERIALS & DESIGN
- Microstructure, tensile properties and fracture behavior of high temperature Al–Si–Mg–Cu cast alloys
- (2013) A.M.A. Mohamed et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Nanostructured high-strength molybdenum alloys with unprecedented tensile ductility
- (2013) G. Liu et al. NATURE MATERIALS
- Rapid in situ fabrication of Fe/SiC bulk nanocomposites by selective laser melting directly from a mixed powder of microsized Fe and SiC
- (2013) Bo Song et al. SCRIPTA MATERIALIA
- Elevated temperature tensile properties and thermal expansion of CNT/2009Al composites
- (2012) Z.Y. Liu et al. COMPOSITES SCIENCE AND TECHNOLOGY
- Development of TiCN-based cermets: Mechanical properties and wear mechanism
- (2012) Ying Peng et al. INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS
- Effects of Mg content on aging behavior of Al4CuXMg PM alloy
- (2012) Azim Gökçe et al. MATERIALS & DESIGN
- Friction and wear behaviors of Al‐SiC‐B4C composites produced by pressure infiltration method
- (2011) U. Soy et al. INDUSTRIAL LUBRICATION AND TRIBOLOGY
- Microstructural examination and properties of premixed Al–Cu–Mg powder metallurgy alloy
- (2011) Azim Gökçe et al. MATERIALS CHARACTERIZATION
- High temperature tensile and wear behaviour of aluminum silicon alloy
- (2010) G. Rajaram et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Phase constituents and mechanical properties of laser in-situ synthesized TiCN/TiN composite coating on Ti-6Al-4V
- (2010) Yuling Yang et al. SURFACE & COATINGS TECHNOLOGY
- The Fracture Toughness and Toughening Mechanism of Commercially Available Unalloyed Molybdenum and Oxide Dispersion Strengthened Molybdenum with an Equiaxed, Large Grain Structure
- (2009) B.V. Cockeram METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- Effects of trace Mn addition on the elevated temperature tensile strength and microstructure of a low-iron Al–Si piston alloy
- (2007) Zhao Qian et al. MATERIALS LETTERS
Publish scientific posters with Peeref
Peeref publishes scientific posters from all research disciplines. Our Diamond Open Access policy means free access to content and no publication fees for authors.
Learn MoreAdd your recorded webinar
Do you already have a recorded webinar? Grow your audience and get more views by easily listing your recording on Peeref.
Upload Now