Predicting strain-induced martensite in austenitic steels by combining physical modelling and machine learning
出版年份 2020 全文链接
标题
Predicting strain-induced martensite in austenitic steels by combining physical modelling and machine learning
作者
关键词
Strain-induced martensitic transformation, Austenitic steels, Machine learning, Physical modelling, Computational materials design
出版物
MATERIALS & DESIGN
Volume 197, Issue -, Pages 109199
出版商
Elsevier BV
发表日期
2020-10-01
DOI
10.1016/j.matdes.2020.109199
参考文献
相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。- Machine Learning to Predict the Martensite Start Temperature in Steels
- (2019) Moshiour Rahaman et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- Machine learning assisted design of high entropy alloys with desired property
- (2019) Cheng Wen et al. ACTA MATERIALIA
- Physical metallurgy-guided machine learning and artificial intelligent design of ultrahigh-strength stainless steel
- (2019) Chunguang Shen et al. ACTA MATERIALIA
- Micromechanics and microstructure evolution during in situ uniaxial tensile loading of TRIP-assisted duplex stainless steels
- (2018) Ye Tian et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Interplay of microstructure defects in austenitic steel with medium stacking fault energy
- (2016) C. Ullrich et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Deformation Microstructure and Deformation-Induced Martensite in Austenitic Fe-Cr-Ni Alloys Depending on Stacking Fault Energy
- (2016) Ye Tian et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- In situ observation of strain and phase transformation in plastically deformed 301 austenitic stainless steel
- (2016) Yadunandan B. Das et al. MATERIALS & DESIGN
- The difference in thermal and mechanical stabilities of austenite between carbon- and nitrogen-added metastable austenitic stainless steels
- (2015) Takuro Masumura et al. ACTA MATERIALIA
- Experiment and modeling to investigate the effect of stress state, strain and temperature on martensitic phase transformation in TRIP-assisted steel
- (2015) Hwigeon Kim et al. ACTA MATERIALIA
- Nano/ultrafine grained austenitic stainless steel through the formation and reversion of deformation-induced martensite: Mechanisms, microstructures, mechanical properties, and TRIP effect
- (2015) M. Shirdel et al. MATERIALS CHARACTERIZATION
- Effect of copper on the formation of strain-induced martensite in two austenitic stainless steels AISI 304
- (2015) Leonidas Cayo Mamani Gilapa et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Revisiting Stacking Fault Energy of Steels
- (2015) Arpan Das METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- In situ X-ray microdiffraction study of deformation-induced phase transformation in 304 austenitic stainless steel
- (2013) N. Li et al. ACTA MATERIALIA
- The influence of grain size on the strain-induced martensite formation in tensile straining of an austenitic 15Cr–9Mn–Ni–Cu stainless steel
- (2013) A. Kisko et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Investigation of cold rolling variables on the formation of strain-induced martensite in 201L stainless steel
- (2012) A. Rezaee et al. MATERIALS & DESIGN
- Twinning and martensite in a 304 austenitic stainless steel
- (2012) Y.F. Shen et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- In-Situ Measurements of Load Partitioning in a Metastable Austenitic Stainless Steel: Neutron and Magnetomechanical Measurements
- (2012) David Maréchal et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- On the stress state dependence of the twinning rate and work hardening in twinning-induced plasticity steels
- (2012) K. Renard et al. SCRIPTA MATERIALIA
- Evaluation of the dislocation density and dislocation character in cold rolled Type 304 steel determined by profile analysis of X-ray diffraction
- (2011) Takashi Shintani et al. ACTA MATERIALIA
- Estimation of deformation induced martensite in austenitic stainless steels
- (2011) Arpan Das et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Spontaneous and Deformation-Induced Martensite in Austenitic Stainless Steels with Different Stability
- (2011) Reza Naraghi et al. STEEL RESEARCH INTERNATIONAL
- Thermodynamic modeling of the stacking fault energy of austenitic steels
- (2010) S. Curtze et al. ACTA MATERIALIA
- The effect of cold rolling regime on microstructure and mechanical properties of AISI 304L stainless steel
- (2010) Ali Hedayati et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- On deformation twinning in a 17.5% Mn–TWIP steel: A physically based phenomenological model
- (2010) A. Soulami et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Analysis of deformation induced martensitic transformation in stainless steels
- (2010) A. Das et al. MATERIALS SCIENCE AND TECHNOLOGY
- Load Partitioning and Strain-Induced Martensite Formation during Tensile Loading of a Metastable Austenitic Stainless Steel
- (2009) P. Hedström et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- The strain induced martensite transformation in austenitic stainless steels: Part 2 – Effect of internal stresses on mechanical response
- (2008) K. Spencer et al. MATERIALS SCIENCE AND TECHNOLOGY
- The strain induced martensite transformation in austenitic stainless steels: Part 1 – Influence of temperature and strain history
- (2008) K. Spencer et al. MATERIALS SCIENCE AND TECHNOLOGY
- Effect of rolling strain on transformation induced plasticity of austenite to martensite in a high-alloy austenitic steel
- (2007) M. Bigdeli Karimi et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- The effect of cold work on structure and properties of AISI 304 stainless steel
- (2007) M. Milad et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
Find Funding. Review Successful Grants.
Explore over 25,000 new funding opportunities and over 6,000,000 successful grants.
ExploreCreate your own webinar
Interested in hosting your own webinar? Check the schedule and propose your idea to the Peeref Content Team.
Create Now