标题
Investigation on laser-induced oxidation assisted micro-milling of Inconel 718
作者
关键词
-
出版物
PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE
Volume 234, Issue 8, Pages 1102-1112
出版商
SAGE Publications
发表日期
2020-03-12
DOI
10.1177/0954405420904843
参考文献
相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。- Feasibility study of the Ti(C7N3)-based cermet micro-mill based on dynamic fatigue behavior and modeling of the contact stress distribution on the round cutting edge
- (2019) Yishun Wang et al. INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES
- Tool wear mechanisms and micro-channels quality in micro-machining of Ti-6Al-4V alloy using the Ti(C7N3)-based cermet micro-mills
- (2019) Yishun Wang et al. TRIBOLOGY INTERNATIONAL
- Effect of the progressive tool wear on surface topography and chip formation in micro-milling of Ti–6Al–4V using Ti(C7N3)-based cermet micro-mill
- (2019) Yishun Wang et al. TRIBOLOGY INTERNATIONAL
- Laser micro-milling of bio-lox forte ceramic: An experimental analysis
- (2018) Basem M.A. Abdo et al. PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY
- Coupled thermal and mechanical analyses of micro-milling Inconel 718
- (2018) Xiaohong Lu et al. PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE
- Model for the prediction of 3D surface topography and surface roughness in micro-milling Inconel 718
- (2017) Xiaohong Lu et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Fabrication and machining of ceramic composites — A review on current scenario
- (2017) Mandeep Singh Rayat et al. MATERIALS AND MANUFACTURING PROCESSES
- Micro-electrical discharge machining of difficult-to-machine materials: A review
- (2017) Ved Prakash et al. PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE
- Influence of cutting tool geometrical parameters on tool wear in high-speed milling of Inconel 718 curved surface
- (2017) Jian-wei Ma et al. PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE
- Fabrication of stepped hole on zirconia bioceramics by ultrasonic machining
- (2016) S. Das et al. MACHINING SCIENCE AND TECHNOLOGY
- Review on powder-bed laser additive manufacturing of Inconel 718 parts
- (2016) Xiaoqing Wang et al. PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE
- Optimization of machining parameters during micro-milling of Ti6Al4V titanium alloy and Inconel 718 materials using Taguchi method
- (2016) Emel Kuram et al. PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE
- Experimental investigation and processing optimization for micro-milling of copper clad polyimide
- (2016) Kai Zhao et al. PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE
- Fabrication of micro-pin array with high aspect ratio on stainless steel using nanosecond laser beam machining
- (2012) Se Won Lee et al. APPLIED SURFACE SCIENCE
- Wear behavior of coated tools in laser assisted micro-milling of hardened steel
- (2012) Mukund Kumar et al. WEAR
- Process capability study of laser assisted micro milling of a hard-to-machine material
- (2011) Mukund Kumar et al. Journal of Manufacturing Processes
- Laser assisted micro-milling of hard-to-machine materials
- (2009) S. Melkote et al. CIRP ANNALS-MANUFACTURING TECHNOLOGY
Discover Peeref hubs
Discuss science. Find collaborators. Network.
Join a conversationAsk a Question. Answer a Question.
Quickly pose questions to the entire community. Debate answers and get clarity on the most important issues facing researchers.
Get Started