标题
Effect of friction stir processing and hybrid reinforcements on copper
作者
关键词
-
出版物
MATERIALS AND MANUFACTURING PROCESSES
Volume -, Issue -, Pages 1-12
出版商
Informa UK Limited
发表日期
2018-03-29
DOI
10.1080/10426914.2018.1453149
参考文献
相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。- Experimental investigations on the enhancement of mechanical properties of magnesium-based hybrid metal matrix composites through friction stir processing
- (2017) S. Arokiasamy et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Distribution of reinforcement particles in surface composite fabrication via friction stir processing: Suitable strategy
- (2017) Sandeep Rathee et al. MATERIALS AND MANUFACTURING PROCESSES
- Investigations on the effect of friction stir processing on Cu-BN surface composites
- (2017) Titus Thankachan et al. MATERIALS AND MANUFACTURING PROCESSES
- WEDM process parameter optimization of FSPed copper-BN composites
- (2017) Titus Thankachan et al. MATERIALS AND MANUFACTURING PROCESSES
- Microstructural, mechanical and tribological behavior of aluminum nitride reinforced copper surface composites fabricated through friction stir processing route
- (2017) Titus Thankachan et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Parametric optimization of dry sliding wear loss of copper–MWCNT composites
- (2017) K. SOORYA PRAKASH et al. TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA
- On the passive and electrochemical behavior of severely deformed pure Ti through friction stir processing
- (2016) Arash Fattah-alhosseini et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Investigation of hexagonal boron nitride as an atomically thin corrosion passivation coating in aqueous solution
- (2016) Jing Zhang et al. NANOTECHNOLOGY
- Preparation of Al 2 O 3 /TiO 2 particle-reinforced copper through plasma spraying and friction stir processing
- (2016) Chao Li et al. MATERIALS & DESIGN
- Formation and analysis of amorphous and nanocrystalline phases in Al–Cu–Mg alloy under friction stir processing
- (2015) Peng Liu et al. PHILOSOPHICAL MAGAZINE LETTERS
- Mechanical and microstructural characterization of Cu/CNT nanocomposite layers fabricated via friction stir processing
- (2014) Jalal Jafari et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Microstructural, mechanical, and thermophysical characterization of Cu/WC composite layers fabricated via friction stir processing
- (2014) Jahangir Khosravi et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Improving Erosion Resistance of Hydroturbine Steel Using Friction Stir Processing
- (2014) H. S. Grewal et al. JOURNAL OF TRIBOLOGY-TRANSACTIONS OF THE ASME
- Marine Corrosion Protective Coatings of Hexagonal Boron Nitride Thin Films on Stainless Steel
- (2013) Esam Husain et al. ACS Applied Materials & Interfaces
- Tribological Behavior of A356/Al2O3 Surface Nanocomposite Prepared by Friction Stir Processing
- (2013) Y. Mazaheri et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- Friction and wear performance of copper–graphite surface composites fabricated by friction stir processing (FSP)
- (2013) H. Sarmadi et al. WEAR
- Effect of Traverse Speed on Microstructure and Microhardness of Cu/B4C Surface Composite Produced by Friction Stir Processing
- (2013) R. Sathiskumar et al. TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS
- Ultrathin high-temperature oxidation-resistant coatings of hexagonal boron nitride
- (2013) Zheng Liu et al. Nature Communications
- Low-Loss, Silicon Integrated, Aluminum Nitride Photonic Circuits and Their Use for Electro-Optic Signal Processing
- (2012) Chi Xiong et al. NANO LETTERS
- Fabrication of in situ Cu/SiC composites using multi-pass friction stir processing: Evaluation of microstructural, porosity, mechanical and electrical behavior
- (2011) Mohsen Barmouz et al. COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING
- Fabrication of AA6061/Al2O3 nano ceramic particle reinforced composite coating by using friction stir processing
- (2010) Min Yang et al. JOURNAL OF MATERIALS SCIENCE
- Effect of friction stir processing tool probe on fabrication of SiC particle reinforced composite on aluminium surface
- (2009) E. R. I. Mahmoud et al. SCIENCE AND TECHNOLOGY OF WELDING AND JOINING
Find the ideal target journal for your manuscript
Explore over 38,000 international journals covering a vast array of academic fields.
SearchAdd your recorded webinar
Do you already have a recorded webinar? Grow your audience and get more views by easily listing your recording on Peeref.
Upload Now