Increasing adhesive bonding of carbon fiber reinforced thermoplastic matrix by laser surface treatment
出版年份 2017 全文链接
标题
Increasing adhesive bonding of carbon fiber reinforced thermoplastic matrix by laser surface treatment
作者
关键词
-
出版物
POLYMER ENGINEERING AND SCIENCE
Volume 57, Issue 7, Pages 685-692
出版商
Wiley
发表日期
2017-04-25
DOI
10.1002/pen.24577
参考文献
相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。- A prediction-correction scheme for microchannel milling using femtosecond laser
- (2017) Jianxiong Chen et al. OPTICS AND LASERS IN ENGINEERING
- Laser ablation surface preparation for adhesive bonding of carbon fiber reinforced epoxy composites
- (2016) Frank L. Palmieri et al. INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES
- Study of the laser marking process of cold sprayed titanium coatings on aluminium substrates
- (2016) A. Astarita et al. OPTICS AND LASER TECHNOLOGY
- Experimental investigation on laser milling of aluminium oxide using a 30W Q-switched Yb:YAG fiber laser
- (2016) C. Leone et al. OPTICS AND LASER TECHNOLOGY
- Ultraviolet Laser Cleaning of Carbon Fiber Composites
- (2016) R. Delmdahl et al. POWDER METALLURGY AND METAL CERAMICS
- Laser cutting of lithium iron phosphate battery electrodes: Characterization of process efficiency and quality
- (2015) Adrian H.A. Lutey et al. OPTICS AND LASER TECHNOLOGY
- Improvement of bonding strength of scarf-bonded carbon fibre/epoxy laminates by Nd:YAG laser surface activation
- (2014) Henrik Schmutzler et al. COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING
- On a generalized approach to manufacturing energy efficiency
- (2014) Apostolos Fysikopoulos et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Improving adhesion performance of polyethylene surfaces by cold plasma treatment
- (2014) C. Mandolfino et al. MECCANICA
- Investigation of CFRP laser milling using a 30W Q-switched Yb:YAG fiber laser: Effect of process parameters on removal mechanisms and HAZ formation
- (2013) C. Leone et al. COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING
- Multi-objective optimization of laser milling of 5754 aluminum alloy
- (2013) S.L. Campanelli et al. OPTICS AND LASER TECHNOLOGY
- Fibre laser cutting of CFRP thin sheets by multi-passes scan technique
- (2013) C. Leone et al. OPTICS AND LASERS IN ENGINEERING
- Fabrication and impedance measurement of novel metal dry bioelectrode
- (2013) Wei Zhou et al. SENSORS AND ACTUATORS A-PHYSICAL
- An artificial neural network approach for the control of the laser milling process
- (2012) S. L. Campanelli et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Surface analytical characterisation of Nd:YAG-laser pre-treated Al Mg3 as a preparation for bonding
- (2012) M. Langer et al. SOLID STATE SCIENCES
- Laser-based repair of carbon fiber reinforced plastics
- (2010) F. Fischer et al. CIRP ANNALS-MANUFACTURING TECHNOLOGY
- Influence of plasma surface treatment on bond strength behaviour of an adhesively bonded aluminium-epoxy system
- (2010) C. Sperandio et al. INTERNATIONAL JOURNAL OF ADHESION AND ADHESIVES
- AISI 304 stainless steel marking by a Q-switched diode pumped Nd:YAG laser
- (2010) C. Leone et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Modelling of Fluidized Bed Degreasing (FBD) process by ANNs
- (2008) M. Barletta et al. International Journal of Surface Science and Engineering
Find Funding. Review Successful Grants.
Explore over 25,000 new funding opportunities and over 6,000,000 successful grants.
ExploreDiscover Peeref hubs
Discuss science. Find collaborators. Network.
Join a conversation