Microstructure and residual stress modulation of 7075 aluminum alloy for improving fatigue performance by laser shock peening
出版年份 2022 全文链接
标题
Microstructure and residual stress modulation of 7075 aluminum alloy for improving fatigue performance by laser shock peening
作者
关键词
-
出版物
INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
Volume 184, Issue -, Pages 103979
出版商
Elsevier BV
发表日期
2022-11-28
DOI
10.1016/j.ijmachtools.2022.103979
参考文献
相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。- Microstructural modulation of TiAl alloys for controlling ultra-precision machinability
- (2022) Yu Zhang et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- Simulation based compensation techniques to minimize distortion of thin-walled monolithic aluminum parts due to residual stresses
- (2022) Daniel Weber et al. CIRP Journal of Manufacturing Science and Technology
- Analysis of the effects of microstructure heterogeneity on the mechanical behavior of additively manufactured Ti6Al4V using mechanics of structure genome
- (2021) Mohamed G. Elkhateeb et al. MATERIALS & DESIGN
- Investigation of formability, microstructures and post-forming mechanical properties of heat-treatable aluminum alloys subjected to pre-aged hardening warm forming
- (2021) Lin Hua et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- Shear assisted processing and extrusion of enhanced strength aluminum alloy tubing
- (2021) Brandon Scott Taysom et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- Making selective-laser-melted high-strength Al–Mg–Sc–Zr alloy tough via ultrafine and heterogeneous microstructure
- (2021) Zihong Wang et al. SCRIPTA MATERIALIA
- Comparison of Residual Stress Measurements Conducted by X-ray Stress Analysis and Incremental Hole Drilling Method
- (2020) K. Bobzin et al. JOURNAL OF THERMAL SPRAY TECHNOLOGY
- Effects of laser shock peening on the mechanisms of fatigue short crack initiation and propagation of AA7075-T651
- (2020) A.G. Sanchez et al. INTERNATIONAL JOURNAL OF FATIGUE
- Grain refinement mechanism of nickel-based superalloy by severe plastic deformation - Mechanical machining case
- (2019) Zhirong Liao et al. ACTA MATERIALIA
- High-performance integrated additive manufacturing with laser shock peening –induced microstructural evolution and improvement in mechanical properties of Ti6Al4V alloy components
- (2019) Jinzhong Lu et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- Gradient twinning microstructure generated by laser shock peening in an AZ31B magnesium alloy
- (2018) Bo Mao et al. APPLIED SURFACE SCIENCE
- Shock response of nanoporous magnesium by molecular dynamics simulations
- (2018) Guomeng Li et al. INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES
- New interatomic potential for Mg–Al–Zn alloys with specific application to dilute Mg-based alloys
- (2018) Doyl E Dickel et al. MODELLING AND SIMULATION IN MATERIALS SCIENCE AND ENGINEERING
- Study on the effect of laser peening with different power densities on fatigue life of fastener hole
- (2018) Y.F. Jiang et al. OPTICS AND LASER TECHNOLOGY
- Surface gradient microstructural characteristics and evolution mechanism of 2195 aluminum lithium alloy induced by laser shock peening
- (2018) Yang Yang et al. OPTICS AND LASER TECHNOLOGY
- Microstructure characteristics and formation mechanism of TC17 titanium alloy induced by laser shock processing
- (2017) Yang Yang et al. JOURNAL OF ALLOYS AND COMPOUNDS
- Effect of laser shock peening on the high-temperature fatigue performance of 7075 aluminum alloy
- (2017) J.T. Wang et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Nonuniformity of morphology and mechanical properties on the surface of single crystal superalloy subjected to laser shock peening
- (2016) G.X. Lu et al. JOURNAL OF ALLOYS AND COMPOUNDS
- Precipitation behaviour of Al–Zn–Mg–Cu alloy and diffraction analysis from η′ precipitates in four variants
- (2014) Wenchao Yang et al. JOURNAL OF ALLOYS AND COMPOUNDS
- Ultrahigh dense and gradient nano-precipitates generated by warm laser shock peening for combination of high strength and ductility
- (2014) Chang Ye et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Methodology for prediction of distortion of workpieces manufactured by high speed machining based on an accurate through-the-thickness residual stress determination
- (2013) V. Richter-Trummer et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- The interactions of self-interstitials with twin boundaries
- (2012) M.I. Mendelev et al. PHILOSOPHICAL MAGAZINE
- Fatigue performance improvement in AISI 4140 steel by dynamic strain aging and dynamic precipitation during warm laser shock peening
- (2010) Chang Ye et al. ACTA MATERIALIA
- Visualization and analysis of atomistic simulation data with OVITO–the Open Visualization Tool
- (2009) Alexander Stukowski MODELLING AND SIMULATION IN MATERIALS SCIENCE AND ENGINEERING
Find the ideal target journal for your manuscript
Explore over 38,000 international journals covering a vast array of academic fields.
SearchBecome a Peeref-certified reviewer
The Peeref Institute provides free reviewer training that teaches the core competencies of the academic peer review process.
Get Started