Effect of solute Mn on microstructural evolution of Cu–Mn alloys processed by equal channel angular pressing

Effects of stacking fault energy and solute atoms on microstructural evolution of Cu, Ag and Cu–Al alloys processed by equal channel angular pressing

(2020) Mayu Asano et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Grain boundary engineering parameters for ultrafine grained microstructures: Proof of principles by a systematic composition variation in the Cu-Ni system

(2018) Friederike Emeis et al.   ACTA MATERIALIA

Effect of short-range order on microstructure, texture and strain hardening of cold drawn Cu-10 at.%Mn alloy

(2018) Xiaoguang Ma et al.   MATERIALS CHARACTERIZATION

Structural evolutions of metallic materials processed by severe plastic deformation

(2018) Yang Cao et al.   MATERIALS SCIENCE & ENGINEERING R-REPORTS

Significance of stacking fault energy in bulk nanostructured materials: Insights from Cu and its binary alloys as model systems

(2018) X.H. An et al.   PROGRESS IN MATERIALS SCIENCE

A good strength-ductility match in Cu-Mn alloys with high stacking fault energies: Determinant effect of short range ordering

(2017) D. Han et al.   SCRIPTA MATERIALIA

Influence of stacking fault energy and temperature on microstructures and mechanical properties of fcc pure metals processed by equal-channel angular pressing

(2016) Fan Liu et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Influence of dislocation–solute atom interactions and stacking fault energy on grain size of single-phase alloys after severe plastic deformation using high-pressure torsion

(2014) Kaveh Edalati et al.   ACTA MATERIALIA

Extreme grain refinement by severe plastic deformation: A wealth of challenging science

(2013) Y. Estrin et al.   ACTA MATERIALIA

Dynamic and post-dynamic recrystallization under hot, cold and severe plastic deformation conditions

(2013) Taku Sakai et al.   PROGRESS IN MATERIALS SCIENCE

Hardening of pure metals by high-pressure torsion: A physically based model employing volume-averaged defect evolutions

(2012) Marco J. Starink et al.   ACTA MATERIALIA

Effect of stacking fault energy on mechanical behavior of cold-forging Cu and Cu alloys

(2012) X.X. Wu et al.   MATERIALS & DESIGN

The effect of stacking fault energy on equilibrium grain size and tensile properties of nanostructured copper and copper–aluminum alloys processed by equal channel angular pressing

(2012) C.X. Huang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

High-pressure torsion of pure metals: Influence of atomic bond parameters and stacking fault energy on grain size and correlation with hardness

(2011) Kaveh Edalati et al.   ACTA MATERIALIA

The effect of impurity level on ultrafine-grained microstructures and their stability in low stacking fault energy silver

(2011) Zoltán Hegedűs et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Significance of homologous temperature in softening behavior and grain size of pure metals processed by high-pressure torsion

(2011) Kaveh Edalati et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Significance of stacking fault energy on microstructural evolution in Cu and Cu–Al alloys processed by high-pressure torsion

(2011) X.H. An et al.   PHILOSOPHICAL MAGAZINE

Saturation of Fragmentation During Severe Plastic Deformation

(2010) R. Pippan et al.   Annual Review of Materials Research

Influence of stacking fault energy and alloying on stage V hardening of HPT-deformed materials

(2010) Martin Hafok et al.   International Journal of Materials Research

Work-hardening stages of AA1070 and AA6060 after severe plastic deformation

(2010) Matthias Hockauf et al.   JOURNAL OF MATERIALS SCIENCE

Microstructure and mechanical properties of Cu and Cu–Zn alloys produced by equal channel angular pressing

(2010) Z.J. Zhang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Influence of stacking fault energy and short-range ordering on dynamic recovery and work hardening behavior of copper alloys

(2010) Farzad Hamdi et al.   SCRIPTA MATERIALIA

Effect of Mg content on the minimum grain size of Al–Mg alloys obtained by friction stir processing

(2010) Taiki Morishige et al.   SCRIPTA MATERIALIA

Microstructural evolution and mechanical properties of Cu–Al alloys subjected to equal channel angular pressing

(2009) S. Qu et al.   ACTA MATERIALIA

Twinning and dislocation activity in silver processed by severe plastic deformation

(2009) Jeno Gubicza et al.   JOURNAL OF MATERIALS SCIENCE

Correlation between microstructure and mechanical properties of severely deformed metals

(2008) J. Gubicza et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Evolution of defect structures during cold rolling of ultrafine-grained Cu and Cu–Zn alloys: Influence of stacking fault energy

(2007) Y.H. Zhao et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING