Direct evidence of the stacking fault-mediated strain hardening phenomenon

Real-time observations of TRIP-induced ultrahigh strain hardening in a dual-phase CrMnFeCoNi high-entropy alloy

(2020) Sijing Chen et al.   Nature Communications

Correlating work hardening with co-activation of stacking fault strengthening and transformation in a high entropy alloy using in-situ neutron diffraction

(2020) M. Frank et al.   Scientific Reports

Damage-tolerant, corrosion-resistant high entropy alloy with high strength and ductility by laser powder bed fusion additive manufacturing

(2020) Saket Thapliyal et al.   Additive Manufacturing

Corrosion-resistant high entropy alloy with high strength and ductility

(2019) S.S. Nene et al.   SCRIPTA MATERIALIA

Extremely high fatigue resistance in an ultrafine grained high entropy alloy

(2019) K. Liu et al.   Applied Materials Today

VULCAN: A “hammer” for high-temperature materials research

(2019) Ke An et al.   MRS BULLETIN

On the evolving nature of c/a ratio in a hexagonal close-packed epsilon martensite phase in transformative high entropy alloys

(2019) Subhasis Sinha et al.   Scientific Reports

Investigating the deformation mechanisms of a highly metastable high entropy alloy using in-situ neutron diffraction

(2019) M. Frank et al.   Materials Today Communications

Twinning-induced plasticity (TWIP) steels

(2018) Bruno C. De Cooman et al.   ACTA MATERIALIA

Deformation mechanisms and work-hardening behavior of transformation-induced plasticity high entropy alloys by in -situ neutron diffraction

(2018) S. Fu et al.   Materials Research Letters

Strong and Ductile Non-equiatomic High-Entropy Alloys: Design, Processing, Microstructure, and Mechanical Properties

(2017) Zhiming Li et al.   JOM

Stacking-fault strengthening of biomedical Co–Cr–Mo alloy via multipass thermomechanical processing

(2017) Kenta Yamanaka et al.   Scientific Reports

Enhanced strength and ductility in a friction stir processing engineered dual phase high entropy alloy

(2017) S. S. Nene et al.   Scientific Reports

The α -factor in the Taylor flow-stress law in monotonic, cyclic and quasi-stationary deformations: Dependence on slip mode, dislocation arrangement and density

(2016) Haël Mughrabi   CURRENT OPINION IN SOLID STATE & MATERIALS SCIENCE

Metastable high-entropy dual-phase alloys overcome the strength–ductility trade-off

(2016) Zhiming Li et al.   NATURE

Strong grain-size effect on deformation twinning of an Al0.1CoCrFeNi high-entropy alloy

(2016) S. W. Wu et al.   Materials Research Letters

In-situ neutron diffraction study of deformation behavior of a multi-component high-entropy alloy

(2014) Y. Wu et al.   APPLIED PHYSICS LETTERS

Revealing the cyclic hardening mechanism of an austenitic stainless steel by real-time in situ neutron diffraction

(2014) D. Yu et al.   SCRIPTA MATERIALIA

Physics and model of strengthening by parallel stacking faults

(2013) W. W. Jian et al.   APPLIED PHYSICS LETTERS

Ultrastrong Mg Alloy via Nano-spaced Stacking Faults

(2013) W. W. Jian et al.   Materials Research Letters

Dislocation and twin substructure evolution during strain hardening of an Fe–22wt.% Mn–0.6wt.% C TWIP steel observed by electron channeling contrast imaging

(2011) I. Gutierrez-Urrutia et al.   ACTA MATERIALIA

The conflicts between strength and toughness

(2011) Robert O. Ritchie   NATURE MATERIALS

Neutron diffraction measurements of residual stresses in friction stir welding: a review

(2011) W Woo et al.   SCIENCE AND TECHNOLOGY OF WELDING AND JOINING

The effect of grain size and grain orientation on deformation twinning in a Fe–22wt.% Mn–0.6wt.% C TWIP steel

(2010) I. Gutierrez-Urrutia et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

First In Situ Lattice Strains Measurements Under Load at VULCAN

(2010) Ke An et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE