Towards a generally applicable methodology for the characterization of particle properties relevant to processing in powder bed fusion of polymers – From single particle to bulk solid behavior
出版年份 2021 全文链接
标题
Towards a generally applicable methodology for the characterization of particle properties relevant to processing in powder bed fusion of polymers – From single particle to bulk solid behavior
作者
关键词
Powder bed fusion, Powder characterization, Powder flowability, Powder aging, Polyamide 12
出版物
Additive Manufacturing
Volume 41, Issue -, Pages 101957
出版商
Elsevier BV
发表日期
2021-03-19
DOI
10.1016/j.addma.2021.101957
参考文献
相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。- A simple method for assessing powder spreadability for additive manufacturing
- (2020) Moustafa Ahmed et al. POWDER TECHNOLOGY
- Development of Polyoxymethylene Particles via the Solution-Dissolution Process and Application to the Powder Bed Fusion of Polymers
- (2020) Maximilian A. Dechet et al. Materials
- Effect of gas-particle interaction on roller spreading process in additive manufacturing
- (2020) Wenguang Nan et al. POWDER TECHNOLOGY
- Bottom‐Up Design of Composite Supraparticles for Powder‐Based Additive Manufacturing
- (2020) Herbert Canziani et al. Small
- Powders flowability assessment in granular compaction: What about the consistency of Hausner ratio?
- (2019) A. Saker et al. POWDER TECHNOLOGY
- Production and Processing of a Spherical Polybutylene Terephthalate Powder for Laser Sintering
- (2019) Rob Kleijnen et al. Applied Sciences-Basel
- Cohesive Powder Flow: Trends and Challenges in Characterisation and Analysis
- (2019) Mojtaba Ghadiri et al. KONA Powder and Particle Journal
- Numerical simulation of particle flow and segregation during roller spreading process in additive manufacturing
- (2019) Wenguang Nan et al. POWDER TECHNOLOGY
- Jamming during particle spreading in additive manufacturing
- (2018) Wenguang Nan et al. POWDER TECHNOLOGY
- Production of polyamide 11 microparticles for Additive Manufacturing by liquid-liquid phase separation and precipitation
- (2018) Maximilian A. Dechet et al. CHEMICAL ENGINEERING SCIENCE
- Optimisation of blade type spreaders for powder bed preparation in Additive Manufacturing using DEM simulations
- (2017) S. Haeri POWDER TECHNOLOGY
- Comparison of crystallization characteristics and mechanical properties of poly(butylene terephthalate) processed by laser sintering and injection molding
- (2017) S. Arai et al. MATERIALS & DESIGN
- Optimized polybutylene terephthalate powders for selective laser beam melting
- (2016) Jochen Schmidt et al. CHEMICAL ENGINEERING SCIENCE
- Particle-based simulation of powder application in additive manufacturing
- (2016) Eric J.R. Parteli et al. POWDER TECHNOLOGY
- Processability of PEEK, a new polymer for High Temperature Laser Sintering (HT-LS)
- (2015) S. Berretta et al. EUROPEAN POLYMER JOURNAL
- An experimental study into the effects of bulk and flow behaviour of laser sintering polymer powders on resulting part properties
- (2015) Stefan Ziegelmeier et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Assessing polymer powder flow for the application of laser sintering
- (2015) Michael Van den Eynde et al. POWDER TECHNOLOGY
- Morphology of polymeric powders in Laser Sintering (LS): From Polyamide to new PEEK powders
- (2014) S. Berretta et al. EUROPEAN POLYMER JOURNAL
- A novel process route for the production of spherical LBM polymer powders with small size and good flowability
- (2014) Jochen Schmidt et al. POWDER TECHNOLOGY
- Determination of robust material qualities and processing conditions for laser sintering of polyamide 12
- (2013) Andreas Wegner et al. POLYMER ENGINEERING AND SCIENCE
- The High Temperature Annular Shear Cell: A modified ring shear tester to measure the flow properties of powders at high temperature
- (2012) Igino Tomasetta et al. ADVANCED POWDER TECHNOLOGY
- Laser sintering of polyamides and other polymers
- (2011) R.D. Goodridge et al. PROGRESS IN MATERIALS SCIENCE
- Round robin test on ring shear testers
- (2010) Dietmar Schulze ADVANCED POWDER TECHNOLOGY
- Recycling of polyamide 12 based powders in the laser sintering process
- (2009) Krassimir Dotchev et al. RAPID PROTOTYPING JOURNAL
- Effects of particle size, particle/matrix interface adhesion and particle loading on mechanical properties of particulate–polymer composites
- (2008) Shao-Yun Fu et al. COMPOSITES PART B-ENGINEERING
- Quantifying Effects of Particulate Properties on Powder Flow Properties Using a Ring Shear Tester
- (2008) Hao Hou et al. JOURNAL OF PHARMACEUTICAL SCIENCES
- Modeling Adhesion Forces between Deformable Bodies by FEM and Hamaker Summation†
- (2008) Hongben Zhou et al. LANGMUIR
- Additive Processing of Polymers
- (2008) Bettina Wendel et al. MACROMOLECULAR MATERIALS AND ENGINEERING
- Deterioration of polyamide powder properties in the laser sintering process
- (2008) D T Pham et al. PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART C-JOURNAL OF MECHANICAL ENGINEERING SCIENCE
Find the ideal target journal for your manuscript
Explore over 38,000 international journals covering a vast array of academic fields.
SearchBecome a Peeref-certified reviewer
The Peeref Institute provides free reviewer training that teaches the core competencies of the academic peer review process.
Get Started