Electromagnetic-thermal coupling behaviors and thermal convection during two-phase zone continuous casting high strength aluminum alloy tube

Thermal characteristics of induction heating with stepped diameter mold during two-phase zone continuous casting high-strength aluminum alloys

(2020) Yaohua Yang et al.   INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER

Numerical modeling of annular electromagnetic stirring with intercooling in direct chill casting of 7005 aluminum alloy billet

(2019) Yajun Luo et al.   Progress in Natural Science-Materials International

Numerical examination of the evaporation process within a vacuum induction furnace with a comparison to experimental results

(2019) Piotr Buliński et al.   APPLIED THERMAL ENGINEERING

A novel method to prepare columnar grains of TiAl alloys by controlling induction heating

(2019) Yangli Liu et al.   INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER

Thermal characteristics and uniformity of microstructures during temperature controlled mold continuous casting profiled copper alloy strip

(2019) Xuefeng Liu et al.   INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER

Dominant dimensionless parameters controlling solute transfer during electromagnetic cold crucible melting and directional solidifying TiAl alloys

(2018) Yaohua Yang et al.   INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER

Numerical analysis for electromagnetic field influence on heat transfer behaviors in cold crucible used for directional solidification

(2018) Yaohua Yang et al.   INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER

Numerical simulation for macrosegregation in direct-chill casting of 2024 aluminum alloy with an extended continuum mixture model

(2018) Hai-jun LUO et al.   TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA

Influence of hydrogen on the propagation of intergranular corrosion defects in 2024 aluminium alloy

(2018) Marie-Laetitia de Bonfils-Lahovary et al.   CORROSION SCIENCE

Determination of the interfacial heat transfer coefficient at the metal-sand mold interface in low pressure sand casting

(2017) A. Zhang et al.   EXPERIMENTAL THERMAL AND FLUID SCIENCE

Investigation of casting–ceramic shell mold interface thermal resistance during solidification process of nickel based superalloy

(2017) D. Szeliga et al.   EXPERIMENTAL THERMAL AND FLUID SCIENCE

Enthalpy porosity model for melting and solidification of pure-substances with large difference in phase specific heats

(2017) Prodyut R. Chakraborty   INTERNATIONAL COMMUNICATIONS IN HEAT AND MASS TRANSFER

Effect of electromagnetic field on distribution of temperature, velocity and concentration during saturated flow in porous media based on Local Thermal Non-Equilibrium models (influent of input power and input velocity)

(2017) Prempreeya Montienthong et al.   INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER

Numerical study of titanium melting by high frequency inductive heating

(2017) Liangliang Lu et al.   INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER

Coupled electromagnetic and thermal analysis of induction heating for the forging of marine crankshafts

(2016) Min Churl Song et al.   APPLIED THERMAL ENGINEERING

Effect of cooling rate on the solidification characteristics and dendrite coherency point of ADC12 aluminum die casting alloy using thermal analysis

(2016) M. Malekan et al.   JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY

A computational study of low-head direct chill slab casting of aluminum alloy AA2024

(2015) Mainul Hasan et al.   HEAT AND MASS TRANSFER

Microstructure, Macrosegregation, and Thermal Analysis of Direct Chill Cast AA5182 Aluminum Alloy

(2015) N. Jamaly et al.   JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE

Surface quality, microstructure and mechanical properties of Cu–Sn alloy plate prepared by two-phase zone continuous casting

(2015) Xue-feng LIU et al.   TRANSACTIONS OF NONFERROUS METALS SOCIETY OF CHINA

Effect of Cooling Rate on the Dendrite Coherency Point During Solidification of Al2024 Alloy

(2014) M. H. Ghoncheh et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Evaluation of formation of intermetallic compounds in Al2024 alloy using thermal analysis technique

(2014) S.G. Shabestari et al.   THERMOCHIMICA ACTA

Recent developments in advanced aircraft aluminium alloys

(2013) Tolga Dursun et al.   MATERIALS & DESIGN

Microstructure and material properties of an Al–Cu alloy provided by the Ohno continuous casting technique

(2010) Mitsuhiro Okayasu et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Mechanical properties of Al–Si13–Ni1.4–Mg1.4–Cu1 alloys produced by the Ohno continuous casting process

(2010) Mitsuhiro Okayasu et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Application of electromagnetic stirring for the homogenization of aluminium billet cast in a semi-continuous machine

(2009) C. Mapelli et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Rapid air film continuous casting of aluminum alloy using static magnetic field

(2009) Fu QU et al.   Acta Metallurgica Sinica-English Letters

Experimental investigation of heat transport and solidification during low frequency electromagnetic hot-top casting of 6063 aluminum alloy

(2008) Xiangjie Wang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Macrosegregation in direct-chill casting of aluminium alloys

(2007) R. Nadella et al.   PROGRESS IN MATERIALS SCIENCE