Influences of the compressed dry air-based active cooling on external and internal qualities of wire-arc additive manufactured thin-walled SS308L components
出版年份 2020 全文链接
标题
Influences of the compressed dry air-based active cooling on external and internal qualities of wire-arc additive manufactured thin-walled SS308L components
作者
关键词
Wire-arc additive manufacturing, Active cooling, SS308L, Microstructure evolution, Mechanical properties
出版物
Journal of Manufacturing Processes
Volume 62, Issue -, Pages 18-27
出版商
Elsevier BV
发表日期
2020-12-22
DOI
10.1016/j.jmapro.2020.11.046
参考文献
相关参考文献
注意：仅列出部分参考文献，下载原文获取全部文献信息。- Concept and validation of an active cooling technique to mitigate heat accumulation in WAAM
- (2020) Leandro João da Silva et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- An experimental-numerical study of active cooling in wire arc additive manufacturing
- (2020) William Hackenhaar et al. Journal of Manufacturing Processes
- Microstructural and mechanical characteristics of 308L stainless steel manufactured by gas metal arc welding-based additive manufacturing
- (2020) Van Thao Le et al. MATERIALS LETTERS
- Increasing the manufacturing efficiency of WAAM by advanced cooling strategies
- (2020) Uwe Reisgen et al. Welding in the World
- Forming Process, Microstructure, and Mechanical Properties of Thin-Walled 316L Stainless Steel Using Speed-Cold-Welding Additive Manufacturing
- (2019) Wei Wu et al. Metals
- Correlation between arc mode, microstructure, and mechanical properties during wire arc additive manufacturing of 316L stainless steel
- (2019) Leilei Wang et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Comparative study of 316L depositions by two welding current processes
- (2019) Wei Wu et al. MATERIALS AND MANUFACTURING PROCESSES
- Effect of heat input on microstructure and mechanical properties of Al-Mg alloys fabricated by WAAM
- (2019) Chuanchu Su et al. APPLIED SURFACE SCIENCE
- Microstructural evolution and mechanical properties of a low-carbon low-alloy steel produced by wire arc additive manufacturing
- (2019) Mehran Rafieazad et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Steels in additive manufacturing: A review of their microstructure and properties
- (2019) P. Bajaj et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Microstructure and mechanical properties of 308L stainless steel fabricated by laminar plasma additive manufacturing
- (2019) Miao Li et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Effect of inter layer idle time on thermal behavior for multi-layer single-pass thin-walled parts in GMAW-based additive manufacturing
- (2018) Yangyang Lei et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Influences of process parameters on surface roughness of multi-layer single-pass thin-walled parts in GMAW-based additive manufacturing
- (2018) Jun Xiong et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- The effects of forced interpass cooling on the material properties of wire arc additively manufactured Ti6Al4V alloy
- (2018) Bintao Wu et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- A review of wire arc additive manufacturing and advances in wire arc additive manufacturing of aluminium
- (2018) K. S. Derekar MATERIALS SCIENCE AND TECHNOLOGY
- A review of the wire arc additive manufacturing of metals: properties, defects and quality improvement
- (2018) Bintao Wu et al. Journal of Manufacturing Processes
- Open-source wire and arc additive manufacturing system: formability, microstructures, and mechanical properties
- (2017) X. Lu et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Thermal analysis for single-pass multi-layer GMAW based additive manufacturing using infrared thermography
- (2017) Dongqing Yang et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Effects of heat accumulation on the arc characteristics and metal transfer behavior in Wire Arc Additive Manufacturing of Ti6Al4V
- (2017) Bintao Wu et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Laser metal deposition of multi-track walls of 308LSi stainless steel
- (2017) T. E. Abioye et al. MATERIALS AND MANUFACTURING PROCESSES
- Microstructure and mechanical properties of the austenitic stainless steel 316L fabricated by gas metal arc additive manufacturing
- (2017) Xiaohui Chen et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Effect of process parameters on the quality of aluminium alloy Al5Si deposits in wire and arc additive manufacturing using a cold metal transfer process
- (2017) A. Gomez Ortega et al. SCIENCE AND TECHNOLOGY OF WELDING AND JOINING
- Additive manufacturing of metals
- (2016) Dirk Herzog et al. ACTA MATERIALIA
- Wire + Arc Additive Manufacturing
- (2016) S. W. Williams et al. MATERIALS SCIENCE AND TECHNOLOGY
- Microstructure evolution and mechanical properties of multiple-layer laser cladding coating of 308L stainless steel
- (2015) Kaibin Li et al. APPLIED SURFACE SCIENCE
- Wire-feed additive manufacturing of metal components: technologies, developments and future interests
- (2015) Donghong Ding et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Influence of defects on mechanical properties of Ti–6Al–4V components produced by selective laser melting and electron beam melting
- (2015) Haijun Gong et al. MATERIALS & DESIGN
- Effects of Interpass Idle Time on Thermal Stresses in Multipass Multilayer Weld-Based Rapid Prototyping
- (2013) Huihui Zhao et al. JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME
- Characterization of stainless steel parts by Laser Metal Deposition Shaping
- (2013) Kai Zhang et al. MATERIALS & DESIGN
- On the mechanical behaviour of titanium alloy TiAl6V4 manufactured by selective laser melting: Fatigue resistance and crack growth performance
- (2012) S. Leuders et al. INTERNATIONAL JOURNAL OF FATIGUE
- Compression fatigue behavior of Ti–6Al–4V mesh arrays fabricated by electron beam melting
- (2011) S.J. Li et al. ACTA MATERIALIA
- Low cost integration of additive and subtractive processes for hybrid layered manufacturing
- (2010) K.P. Karunakaran et al. ROBOTICS AND COMPUTER-INTEGRATED MANUFACTURING
- Dendrite growth simulation during solidification in the LENS process
- (2009) H. Yin et al. ACTA MATERIALIA
- Microstructure evolution in AISI 304 stainless steel during near rapid directional solidification
- (2009) J. W. Fu et al. MATERIALS SCIENCE AND TECHNOLOGY
Find Funding. Review Successful Grants.
Explore over 25,000 new funding opportunities and over 6,000,000 successful grants.
ExploreFind the ideal target journal for your manuscript
Explore over 38,000 international journals covering a vast array of academic fields.
Search