Defect structure process maps for laser powder bed fusion additive manufacturing

Keyhole threshold and morphology in laser melting revealed by ultrahigh-speed x-ray imaging

(2019) Ross Cunningham et al.   SCIENCE

Transient dynamics of powder spattering in laser powder bed fusion additive manufacturing process revealed by in-situ high-speed high-energy x-ray imaging

(2018) Qilin Guo et al.   ACTA MATERIALIA

Feedstock powder processing research needs for additive manufacturing development

(2018) Iver E. Anderson et al.   CURRENT OPINION IN SOLID STATE & MATERIALS SCIENCE

A comparative study of Ti-6Al-4V powders for additive manufacturing by gas atomization, plasma rotating electrode process and plasma atomization

(2018) G. Chen et al.   POWDER TECHNOLOGY

Influence of defects, surface roughness and HIP on the fatigue strength of Ti-6Al-4V manufactured by additive manufacturing

(2018) Hiroshige Masuo et al.   INTERNATIONAL JOURNAL OF FATIGUE

Oxides, porosity and fatigue performance of AlSi10Mg parts produced by selective laser melting

(2017) Ming Tang et al.   INTERNATIONAL JOURNAL OF FATIGUE

Review of the Methods for Production of Spherical Ti and Ti Alloy Powder

(2017) Pei Sun et al.   JOM

Synchrotron-Based X-ray Microtomography Characterization of the Effect of Processing Variables on Porosity Formation in Laser Power-Bed Additive Manufacturing of Ti-6Al-4V

(2017) Ross Cunningham et al.   JOM

Microstructural characterization and properties of Ti-28Ta at.% powders produced by plasma rotating electrode process

(2017) J.O. Yin et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Analyzing the effects of powder and post-processing on porosity and properties of electron beam melted Ti-6Al-4V

(2017) Ross Cunningham et al.   Materials Research Letters

Laser powder-bed fusion additive manufacturing: Physics of complex melt flow and formation mechanisms of pores, spatter, and denudation zones

(2016) Saad A. Khairallah et al.   ACTA MATERIALIA

Metal Additive Manufacturing: A Review of Mechanical Properties

(2016) John J. Lewandowski et al.   Annual Review of Materials Research

Overview of Materials Qualification Needs for Metal Additive Manufacturing

(2016) Mohsen Seifi et al.   JOM

Mechanical behavior of additive manufactured, powder-bed laser-fused materials

(2016) Todd M. Mower et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Process Optimization of Dual-Laser Beam Welding of Advanced Al-Li Alloys Through Hot Cracking Susceptibility Modeling

(2016) Yingtao Tian et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

The Effectiveness of Hot Isostatic Pressing for Closing Porosity in Titanium Parts Manufactured by Selective Electron Beam Melting

(2016) Samuel Tammas-Williams et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

3D imaging and quantification of porosity in electron beam welded dissimilar steel to Fe-Al alloy joints by X-ray tomography

(2016) Soumitra Kumar Dinda et al.   MATERIALS & DESIGN

Review of in-situ process monitoring and in-situ metrology for metal additive manufacturing

(2016) Sarah K. Everton et al.   MATERIALS & DESIGN

XCT analysis of the influence of melt strategies on defect population in Ti–6Al–4V components manufactured by Selective Electron Beam Melting

(2015) S. Tammas-Williams et al.   MATERIALS CHARACTERIZATION

Metal Additive Manufacturing: A Review

(2014) William E. Frazier   JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE

Observation of keyhole-mode laser melting in laser powder-bed fusion additive manufacturing

(2014) Wayne E. King et al.   JOURNAL OF MATERIALS PROCESSING TECHNOLOGY

Fatigue performance evaluation of selective laser melted Ti–6Al–4V

(2014) P. Edwards et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Porosity Measurements and Analysis for Metal Additive Manufacturing Process Control

(2014) John A. Slotwinski et al.   JOURNAL OF RESEARCH OF THE NATIONAL INSTITUTE OF STANDARDS AND TECHNOLOGY

Fatigue performance of additive manufactured metallic parts

(2013) A.B. Spierings et al.   RAPID PROTOTYPING JOURNAL

On the mechanical behaviour of titanium alloy TiAl6V4 manufactured by selective laser melting: Fatigue resistance and crack growth performance

(2012) S. Leuders et al.   INTERNATIONAL JOURNAL OF FATIGUE

Porosity formation and gas bubble retention in laser metal deposition

(2009) G. K. L. Ng et al.   APPLIED PHYSICS A-MATERIALS SCIENCE & PROCESSING