Poly ether ether ketone and its composite powder prepared by thermally induced phase separation for high temperature selective laser sintering

Investigation on dielectrical and space charge characteristics of peek insulation used in aerospace high‐voltage system

(2019) Zili Liu et al.   IEEJ Transactions on Electrical and Electronic Engineering

A primary study into graphene/polyether ether ketone (PEEK) nanocomposite for laser sintering

(2018) Binling Chen et al.   APPLIED SURFACE SCIENCE

Production of spherical semi-crystalline polycarbonate microparticles for Additive Manufacturing by liquid-liquid phase separation

(2018) Stephanie Kloos et al.   POWDER TECHNOLOGY

Additive manufacture of PEEK cranial implants: Manufacturing considerations versus accuracy and mechanical performance

(2018) S. Berretta et al.   MATERIALS & DESIGN

The thermal degradation and dynamic mechanical properties modeling of MWCNT/glass fiber multiscale filler reinforced polypropylene composites

(2018) N. Rasana et al.   COMPOSITES SCIENCE AND TECHNOLOGY

Production of polyamide 11 microparticles for Additive Manufacturing by liquid-liquid phase separation and precipitation

(2018) Maximilian A. Dechet et al.   CHEMICAL ENGINEERING SCIENCE

Poly Aryl Ether Ketones (PAEKs) and carbon-reinforced PAEK powders for laser sintering

(2017) Binling Chen et al.   JOURNAL OF MATERIALS SCIENCE

Functionalization of multi-walled carbon nanotubes and their effect on the tribological properties of poly(ether ether ketone) composites

(2017) Yingshuang Shang et al.   POLYMER INTERNATIONAL

Production of spherical wax and polyolefin microparticles by melt emulsification for additive manufacturing

(2016) Stephanie Fanselow et al.   CHEMICAL ENGINEERING SCIENCE

Spray Drying as a Processing Technique for Syndiotactic Polystyrene to Powder Form for Part Manufacturing Through Selective Laser Sintering

(2016) N. Mys et al.   JOM

Polymer viscosity, particle coalescence and mechanical performance in high-temperature laser sintering

(2016) S. Berretta et al.   JOURNAL OF MATERIALS SCIENCE

Preparation of polypropylene microspheres for selective laser sintering via thermal-induced phase separation: Roles of liquid-liquid phase separation and crystallization

(2016) Shao-Jie Wang et al.   JOURNAL OF POLYMER SCIENCE PART B-POLYMER PHYSICS

Processability of PEEK, a new polymer for High Temperature Laser Sintering (HT-LS)

(2015) S. Berretta et al.   EUROPEAN POLYMER JOURNAL

Gamma irradiation effects on thermal, physical and tribological properties of PEEK under water lubricated conditions

(2015) Neelima Khare et al.   WEAR

Preparation of PA12 microspheres with tunable morphology and size for use in SLS processing

(2015) Gexia Wang et al.   MATERIALS & DESIGN

Powder characteristics, microstructure and properties of graphite platelet reinforced Poly Ether Ether Ketone composites in High Temperature Laser Sintering (HT-LS)

(2015) Yuan Wang et al.   MATERIALS & DESIGN

Experimental study of crystallization of PolyEtherEtherKetone (PEEK) over a large temperature range using a nano-calorimeter

(2014) Xavier Tardif et al.   POLYMER TESTING

Influence of carbon nanotubes on the rheology and dynamic mechanical properties of polyamide-12 for laser sintering

(2014) Jiaming Bai et al.   POLYMER TESTING

Polyamide-12/Functionalized Carbon Nanofiber Composites: Evaluation of Thermal and Mechanical Properties

(2010) Ricardo Chávez-Medellín et al.   MACROMOLECULAR MATERIALS AND ENGINEERING

Processing of a Polyamide-12/carbon nanofibre composite by laser sintering

(2010) R.D. Goodridge et al.   POLYMER TESTING

Effect of carbon nanotubes on the mechanical properties and crystallization behavior of poly(ether ether ketone)

(2009) Changru Rong et al.   COMPOSITES SCIENCE AND TECHNOLOGY

Novel fabrication techniques to produce microspheres by thermally induced phase separation for tissue engineering and drug delivery

(2007) Jonny J. Blaker et al.   Acta Biomaterialia