标题
Superficial Effects of Ball Burnishing on TRIP Steel AISI 301LN Sheets
作者
关键词
-
出版物
Metals
Volume 11, Issue 1, Pages 82
出版商
MDPI AG
发表日期
2021-01-04
DOI
10.3390/met11010082
参考文献
相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。- Monitoring of Processing Conditions of an Ultrasonic Vibration-Assisted Ball-Burnishing Process
- (2020) Aida Estevez-Urra et al. SENSORS
- Selection of optimal process parameters in sustainable diamond burnishing of 17-4 PH stainless steel
- (2019) B. Sachin et al. Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Surface hardening of 36 NiCrMo 6 steel by ball burnishing process
- (2019) Hamid Hamadache et al. Materials Research Express
- Mechanical Surface Treatments of AISI 304 Stainless Steel: Effects on Surface Microrelief, Residual Stress, and Microstructure
- (2019) D. A. Lesyk et al. JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
- Hardening effect and fatigue behavior enhancement through ball burnishing on AISI 1038
- (2019) J.A. Travieso-Rodríguez et al. Journal of Materials Research and Technology-JMR&T
- Roller burnishing of Ti6Al4V under different cooling/lubrication conditions and tool design: effects on surface integrity
- (2019) Giovanna Rotella et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Evolution of microstructure and residual stresses in gradually ground/polished 3Y-TZP
- (2019) J. Minguela et al. JOURNAL OF THE EUROPEAN CERAMIC SOCIETY
- Microstructural evolution mechanisms in rolled 17-4PH steel processed by ultrasonic surface rolling process
- (2019) Dan Liu et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Development, characterization and test of an ultrasonic vibration-assisted ball burnishing tool
- (2018) Ramon Jerez-Mesa et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Topological surface integrity modification of AISI 1038 alloy after vibration-assisted ball burnishing
- (2018) R. Jerez-Mesa et al. SURFACE & COATINGS TECHNOLOGY
- Enhanced fatigue performance and surface mechanical properties of AISI 304 stainless steel induced by electropulsing-assisted ultrasonic surface rolling process
- (2018) Hai-bo Wang et al. JOURNAL OF MATERIALS RESEARCH
- Comprehensive analysis of surface integrity modification of ball-end milled Ti-6Al-4V surfaces through vibration-assisted ball burnishing
- (2018) R. Jerez-Mesa et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Effect of ultrasonic surface rolling at low temperatures on surface layer microstructure and properties of HIP Ti-6Al-4V alloy
- (2017) Gang Li et al. SURFACE & COATINGS TECHNOLOGY
- Microstructure and surface properties of 17-4PH stainless steel by ultrasonic surface rolling technology
- (2017) Qinglong Zhang et al. SURFACE & COATINGS TECHNOLOGY
- Effects of the different frequencies and loads of ultrasonic surface rolling on surface mechanical properties and fretting wear resistance of HIP Ti–6Al–4V alloy
- (2016) G. Li et al. APPLIED SURFACE SCIENCE
- Experimental study of lateral pass width in conventional and vibrations-assisted ball burnishing
- (2016) G. Gomez–Gras et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Effect of electropulsing on surface mechanical properties and microstructure of AISI 304 stainless steel during ultrasonic surface rolling process
- (2016) Haibo Wang et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Influence of multiple ultrasonic impact treatments on surface roughness and wear performance of SUS301 steel
- (2016) Liang Li et al. SURFACE & COATINGS TECHNOLOGY
- Toward control of subsurface strain accumulation in nanostructuring burnishing on thermostrengthened steel
- (2016) V.P. Kuznetsov et al. SURFACE & COATINGS TECHNOLOGY
- Effect of shot peening on metastable austenitic stainless steels
- (2015) G. Fargas et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Correlation Between Microstructure and Mechanical Properties Before and After Reversion of Metastable Austenitic Stainless Steels
- (2015) Gemma Fargas et al. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE
- Influence of severe shot peening on wear behaviour of an aluminium alloy
- (2014) M. Palacios et al. FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES
- Effect of nitriding and shot-peening on the fatigue behavior of 42CrMo4 steel: Experimental analysis and predictive approach
- (2011) Mohamed Ali Terres et al. MATERIALS & DESIGN
- New insight on acoustoplasticity – Ultrasonic irradiation enhances subgrain formation during deformation
- (2010) K.W. Siu et al. INTERNATIONAL JOURNAL OF PLASTICITY
- Deformation-induced martensite formation during cyclic deformation of metastable austenitic steel: Influence of temperature and carbon content
- (2007) U. Krupp et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
Add your recorded webinar
Do you already have a recorded webinar? Grow your audience and get more views by easily listing your recording on Peeref.
Upload NowAsk a Question. Answer a Question.
Quickly pose questions to the entire community. Debate answers and get clarity on the most important issues facing researchers.
Get Started