Microstructure and properties of 3D-printed alumina ceramics with different heating rates in vacuum debinding

Photosensitive ZrO2 suspensions for stereolithography

(2019) Keqiang Zhang et al.   CERAMICS INTERNATIONAL

Effect of heating rate on the strength of ZrB2–SiC composite subjected to cyclic thermal shock

(2019) Xing Yue et al.   CERAMICS INTERNATIONAL

Mechanical properties and microstructures of 3D printed bulk cordierite parts

(2019) Zhangwei Chen et al.   CERAMICS INTERNATIONAL

Additive manufacturing of thin alumina ceramic cores using binder-jetting

(2019) Shuangjun Huang et al.   Additive Manufacturing

PZT ceramics fabricated based on stereolithography for an ultrasound transducer array application

(2018) Yan Chen et al.   CERAMICS INTERNATIONAL

3D printing of ceramics: A review

(2018) Zhangwei Chen et al.   JOURNAL OF THE EUROPEAN CERAMIC SOCIETY

Surface modification of α-Al 2 O 3 with dicarboxylic acids for the preparation of UV-curable ceramic suspensions

(2017) Shuai Zhang et al.   JOURNAL OF THE EUROPEAN CERAMIC SOCIETY

Mechanical Properties, Cytocompatibility and Manufacturability of Chitosan:PEGDA Hybrid-Gel Scaffolds by Stereolithography

(2016) Viola B. Morris et al.   ANNALS OF BIOMEDICAL ENGINEERING

Ceramic Stereolithography: Additive Manufacturing for Ceramics by Photopolymerization

(2016) John W. Halloran   Annual Review of Materials Research

Preparation of a defect-free alumina cutting tool via additive manufacturing based on stereolithography – Optimization of the drying and debinding processes

(2016) Maopeng Zhou et al.   CERAMICS INTERNATIONAL

Effect of the particle size and the debinding process on the density of alumina ceramics fabricated by 3D printing based on stereolithography

(2016) Haidong Wu et al.   CERAMICS INTERNATIONAL

Research on selective laser sintering of Kaolin–epoxy resin ceramic powders combined with cold isostatic pressing and sintering

(2016) Kai Liu et al.   CERAMICS INTERNATIONAL

Aqueous gel casting of water-soluble calcia-based ceramic core for investment casting using epoxy resin as a binder

(2016) Fuchu Liu et al.   INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY

Alumina ceramics with uniform grains prepared from Al 2 O 3 nanospheres

(2016) Zhiqiang Sun et al.   JOURNAL OF ALLOYS AND COMPOUNDS

Stereolithography of SiOC Ceramic Microcomponents

(2015) Erika Zanchetta et al.   ADVANCED MATERIALS

Effectiveness of wick-debinding inside powder bed for ceramic laminates made by tape casting

(2015) Lovro Gorjan et al.   POWDER TECHNOLOGY

Investigation on cristobalite crystallization in silica-based ceramic cores for investment casting

(2013) A. Kazemi et al.   JOURNAL OF THE EUROPEAN CERAMIC SOCIETY

Prediction of recrystallization in investment cast single-crystal superalloys

(2012) Chinnapat Panwisawas et al.   ACTA MATERIALIA

Conditions of applying Oliver–Pharr method to the nanoindentation of particles in composites

(2012) Wenyi Yan et al.   COMPOSITES SCIENCE AND TECHNOLOGY

Transparent alumina by vacuum sintering

(2012) Gustavo Mata-Osoro et al.   JOURNAL OF THE EUROPEAN CERAMIC SOCIETY

Process parameters appraisal of fabricating ceramic parts based on stereolithography using the Taguchi method

(2012) Zhangwei Chen et al.   PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE

Influence of powder morphology on properties of ceramic injection moulding feedstocks

(2011) Anne Mannschatz et al.   JOURNAL OF THE EUROPEAN CERAMIC SOCIETY

Ceramic composite components with gradient porosity by powder injection moulding

(2009) S.X. Zhang et al.   MATERIALS & DESIGN

Analysis of load-penetration depth data using Oliver–Pharr and Cheng–Cheng methods of SiAlON–ZrO2ceramics

(2008) Osman Sahin et al.   JOURNAL OF PHYSICS D-APPLIED PHYSICS

A simple procedure to prepare spherical α-alumina powders

(2008) Hongyu Liu et al.   MATERIALS RESEARCH BULLETIN