标题
Processing of T6 heat-treated Al-12Si-0.6Mg alloy
作者
关键词
-
出版物
MATERIALS AND MANUFACTURING PROCESSES
Volume -, Issue -, Pages 1-9
出版商
Informa UK Limited
发表日期
2020-02-25
DOI
10.1080/10426914.2020.1732412
参考文献
相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。- Effect of metallurgical parameters on the drilling and tapping characteristics of aluminum cast alloys
- (2019) H. Barakat et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Effect of Strontium and Magnesium Additions on the Microstructure and Mechanical Properties of Al–12Si Alloys
- (2019) Ali Paşa Hekimoğlu et al. METALS AND MATERIALS INTERNATIONAL
- Correlation between serrated chip formation and turning chatter in the dry turning of superalloy
- (2019) Shi Limin FERROELECTRICS
- Frictional and wear performance of TiAlN/TiN coated tool against high-strength steel
- (2018) Guangming Zheng et al. CERAMICS INTERNATIONAL
- Effect of V and Zr microalloying, and heat treatment on microstructure and mechanical properties of secondary Al-7Si-3Cu-0.3Mg alloy
- (2018) Jovid Rakhmonov et al. International Journal of Materials Research
- Statistical analysis of cutting forces and hole accuracy in reaming an Al–Si–Mg alloy (6351) with different copper contents
- (2018) Ricardo Augusto Gonçalves et al. Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Micro-machinability of bulk metallic glass in ultra-precision cutting
- (2017) Xiao Chen et al. MATERIALS & DESIGN
- Effect of Aging Conditions on Precipitation Hardening in Al–Si–Mg and Al–Si–Cu–Mg Alloys
- (2016) Mohamed F. Ibrahim et al. International Journal of Metalcasting
- Tribological behavior of Al–6.5%, –12%, –18.5% Si alloys during machining using CVD diamond and DLC coated tools
- (2015) S. Bhowmick et al. SURFACE & COATINGS TECHNOLOGY
- Intermetallic phases in Al–Si based cast alloys: new perspective
- (2013) E. Samuel et al. INTERNATIONAL JOURNAL OF CAST METALS RESEARCH
- Effect of Machining Parameters on Cutting Forces and Surface Roughness in Al-(1-2) Fe-1V-1Si Alloys
- (2013) B. N. Pathak et al. MATERIALS AND MANUFACTURING PROCESSES
- Influence of Flow-Forming Process on Cutting Force Changes in Machining of 99.5% Al Workpiece
- (2012) Sabahudin Ekinovic et al. MATERIALS AND MANUFACTURING PROCESSES
- Analysis of the evolution of the Built-Up Edge and Built-Up Layer formation mechanisms in the dry turning of aeronautical aluminium alloys
- (2012) A. Gómez-Parra et al. WEAR
- The heat treatment of Al–Si–Cu–Mg casting alloys
- (2010) Emma Sjölander et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Effects of Fe intermetallics on the machinability of heat-treated Al–(7–11)% Si alloys
- (2009) Y. Zedan et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- The effects of aging on machinability of 6061 aluminium alloy
- (2008) Halil Demir et al. MATERIALS & DESIGN
- Machining of LM13 and LM28 cast aluminium alloys: Part I
- (2007) D.K. Dwivedi et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
Find Funding. Review Successful Grants.
Explore over 25,000 new funding opportunities and over 6,000,000 successful grants.
ExploreAsk a Question. Answer a Question.
Quickly pose questions to the entire community. Debate answers and get clarity on the most important issues facing researchers.
Get Started