Article
Chemistry, Applied
Inaki Adanez-Rubio, Hector Bautista, Maria Teresa Izquierdo, Pilar Gayan, Alberto Abad, Juan Adanez
Summary: This study investigated the influence of CuO fraction, preparation method, and calcination conditions on the performance of oxygen carriers for the CLOU process. Three oxygen carriers with good Cu activity, reactivity, and magnetism were selected for evaluation in a batch fluidized bed reactor. Both oxygen carriers exhibited high reactivity for gaseous oxygen release, sustained reactivity and magnetism with redox cycles, as well as low attrition rates and no agglomeration problems.
FUEL PROCESSING TECHNOLOGY
(2021)
Article
Energy & Fuels
Ashwani Kumar Dubey, Arunkumar Samanta, Pinaki Sarkar, Vinod Kumar Saxena
Summary: The study examined the effectiveness of CuO as an oxygen carrier in the chemical looping with oxygen uncoupling (CLOU) process using three Indian coals. It was found that the combustion reaction was most suitable at a mass ratio of 1:30 and 850 degrees C, with good repeatability over multiple cycles and minor agglomeration. Additionally, the kinetic analysis indicates that the combustion reaction kinetics is likely diffusion-dominated, with apparent activation energies in the range of 38.3-60.1 kJ/mol and 102.6-129.0 kJ/mol for different temperature zones.
Article
Chemistry, Applied
Jinchen Ma, Xin Tian, Bo Zhao, Xiaoshan Li, Yongchun Zhao, Haibo Zhao, Chuguang Zheng
Summary: This study investigates the behavior of mercury and the role of oxygen carrier in the CLOU process of Pingdingshan anthracite, finding that the removal efficiency of Hg-0(g) by the oxygen carrier is 60.71% and the adsorption capacity of Hg(p) is 0.281 μg/g. The oxygen carrier promotes the oxidation of Hg-0(g) and reduces the mercury released in the air.
FUEL PROCESSING TECHNOLOGY
(2021)
Article
Engineering, Environmental
Ming Luo, Yanjun Qin, Jianjun Cai, Lili Qian, Shuxiang Wang, Haiyan Zhang, Lunzheng Zhou, Peng Liu
Summary: This study investigated the release and migration characteristics of sulfur in the chemical looping combustion of coal with two different synthetic oxygen carriers. The results showed that sulfur behavior varied under different conditions, with sulfur mainly migrating to metal sulfides at lower temperatures and peroxide coefficients.
PROCESS SAFETY AND ENVIRONMENTAL PROTECTION
(2021)
Article
Thermodynamics
Ali Ahmad, Md. Abdullah Al Mamun, Md. Al-Mamun, Saiful Huque, Mohammad Ismail
Summary: This study prepared various oxygen carrier materials using the citrate gel technique and conducted research on the chemical-looping process, finding that the oxygen release rate varied under different experimental conditions after increasing the surface area.
JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY
(2022)
Article
Energy & Fuels
Huan Zhou, Guoqiang Wei, Qun Yi, Zheming Zhang, Yingjie Zhao, Yuke Zhang, Zhen Huang, Anqing Zheng, Kun Zhao, Zengli Zhao
Summary: Chemical looping gasification (CLG) of Yunnan lignite with Fe-Mn mixed oxygen carriers (OCs) was conducted to produce high-purity synthesis gas and reduce pollutant emissions. The Fe-Mn composite OCs exhibited oxygen decoupling characteristics and synergistic effects between active components, making them suitable for the gasification process.
Article
Chemistry, Applied
Doki Yamaguchi, Liangguang Tang, Jose Orellana, Trevor D. Hadley, Sankar Bhattacharya, Kok-Seng Lim
Summary: The study developed a compact fully looped chemical looping reactor and found that the CLC performance increased with increasing operation time over 36 hours, as indicated by the increase in the CO2/CO molar ratio. The morphology changes and ash interaction of the Australian ilmenite did not noticeably affect the CLC performance or operation during continuous operation.
FUEL PROCESSING TECHNOLOGY
(2021)
Article
Energy & Fuels
Giovanny S. de Oliveira, Ciro E. S. Lobo, Carlos E. A. Padilha, Domingos F. S. Souza, Juan A. C. Ruiz
Summary: Brazil aims to reduce its CO2 emissions by utilizing glycerin in Chemical Looping Combustion (CLC). The study evaluates the feasibility of using glycerin in CLC and finds that the addition of ethanol improves combustion efficiency, while the addition of methanol reduces efficiency.
Article
Thermodynamics
Haodong Huang, Jinchen Ma, Haibo Zhao, Chuguang Zheng
Summary: This work investigates the behavior of coal-derived chlorine in chemical looping combustion (CLC) and the potential adverse impacts of primary gaseous chlorine (HCl) on a Cu-based oxygen carrier (OC). The inactivation mechanism of the sol-gel-derived CuO/Al2O3 OC is studied. It is found that HCl is the main gaseous chlorine in coal CLC and shows high reactivity towards CuO. The presence of HCl can result in corrosion and degradation of the OC.
PROCEEDINGS OF THE COMBUSTION INSTITUTE
(2023)
Review
Environmental Sciences
Siddig Abuelgasim, Wenju Wang, Atif Abdalazeez
Summary: Chemical looping combustion (CLC) is a promising CO2 capture technology that utilizes metal particles to transport oxygen and avoid nitrogen in combustion exhaust. Oxygen carrier is a key parameter in CLC, and tests have shown its feasibility worldwide.
SCIENCE OF THE TOTAL ENVIRONMENT
(2021)
Review
Energy & Fuels
Dunyu Liu, Chaoran Wang, Yunpei Fan, Qiuqi Liu, Xudong Wang, Kailong Xu, Jing Jin, Jingjing Ma, Jinchen Ma
Summary: Chemical looping combustion (CLC) of coal for carbon capture utilization and storage is an effective technology to reduce carbon emission. However, there is uncertainty in mercury emission from both air and fuel reactor. This paper aims to reveal the mechanisms for the transformation of mercury-related species.
Article
Engineering, Environmental
Lei Liu, Zhenshan Li, Zuoan Li, Yngve Larring, Ningsheng Cai
Summary: The MFB-TGA method is effective in measuring fast heterogeneous kinetics of oxygen carriers, overcoming limitations observed in TGA. The study investigated oxygen uncoupling and redox reaction kinetics of CaMn0.5Ti0.375Fe0.125O3-delta, revealing oxidation reactions are chemically controlled, while reduction reactions have both fast and slow stages. Analyzing the MFB-TGA data provided kinetic parameters for both oxygen uncoupling and redox reactions.
CHEMICAL ENGINEERING JOURNAL
(2021)
Article
Energy & Fuels
Inaki Adanez-Rubio, Tobias Mattisson, Marijke Jacobs, Juan Adanez
Summary: Chemical Looping with Oxygen Uncoupling (CLOU) is a technology that separates the oxygen for fuel combustion using an oxygen carrier in a fuel reactor. This study investigates the behavior of Mn/Mg/Si system as oxygen carriers for CLOU. The most reactive oxygen carriers without Si in the structure were found to be M24Mg76 and M48Mg51. These carriers showed good reactivity and mechanical stability in a batch fluidized bed reactor.
Article
Chemistry, Applied
Yunchang Dong, Yanan Wang, Jinchen Ma, Hengfeng Bu, Chuanbao Zheng, Haibo Zhao
Summary: In this study, composite oxygen carriers were prepared using extrusion-spheronization method with fine iron and copper ores as raw materials and inert aluminosilicates as binders. After optimization, the oxygen carriers showed good performance in terms of reactivity and stability, indicating the suitability of the method for large-scale preparation of oxygen carrier particles.
FUEL PROCESSING TECHNOLOGY
(2021)
Article
Energy & Fuels
Felix Donat, Agnieszka Kierzkowska, Christoph R. Muller
Summary: In chemical looping, using Fe and Co as the main and side reaction metals can effectively reduce the extent of carbon deposition and improve the catalytic effect of oxygen carriers on methane decomposition.
Article
Energy & Fuels
Ivan Sampron, Luis F. de Diego, Francisco Garcia-Labiano, Maria T. Izquierdo
Summary: This study investigates the impact of different iron content oxygen carriers on the performance of the BCLG system. The research indicates that oxygen carriers with varying iron levels exhibit similar gasification parameters and tar production under changes in oxygen-to-fuel ratio and fuel reactor temperature.
Article
Energy & Fuels
Alberto Abad, Pilar Gayan, Francisco Garcia-Labiano, Luis F. de Diego, Maria T. Izquierdo, Teresa Mendiara, Juan Adanez
Summary: Chemical looping combustion (CLC) is an innovative technology that combines fuel combustion with CO2 capture using oxygen carriers. This study investigated the performance of CuO/Al2O3 and Fe2O3/Al2O3 particles as oxygen carriers in a CLC unit, and developed a mathematical model to simulate their behavior. The model successfully predicted the combustion performance of these materials in both a smaller-scale unit and a larger-scale unit.
GREENHOUSE GASES-SCIENCE AND TECHNOLOGY
(2023)
Article
Chemistry, Multidisciplinary
Kagan Benzesik, Ahmet Turan, Seref Sonmez, Maria Teresa Izquierdo, Onuralp Yucel
Summary: In this study, Li4SiO4 powders were successfully synthesized by Solution Combustion Synthesis (SCS) technique, and their CO2 sorption performance was tested. The synthesized sample showed high CO2 uptake value in thermobalance test and exhibited good CO2 adsorption capability under simulated industrial off-gas conditions. Additionally, the sample demonstrated good cyclic durability during the sorption/desorption tests.
SEPARATION SCIENCE AND TECHNOLOGY
(2023)
Article
Chemistry, Multidisciplinary
Javier Quilez-Bermejo, Sergio Garcia-Dali, Ayoub Daouli, Andrea Zitolo, Rafael L. S. Canevesi, Melanie Emo, Maria T. Izquierdo, Michael Badawi, Alain Celzard, Vanessa Fierro
Summary: In this study, single atoms and nanoclusters of Fe, Ni, Co, Cu, and Mn were embedded in a well-defined C1N1-type material with internal cavities of approximately 0.6 nm. The nucleation of different metal nanoclusters was achieved by forming metal-nitrogen bonds on four N atoms. After pyrolysis, TM@CNx-type structures were obtained, where TM represents the transition metal and x<1. Fe@CNx and Co@CNx showed promising performance in oxygen reduction reaction and hydrogen evolution reaction respectively, with a Pt-like performance, while Ni@CNx exhibited the highest activity in oxygen evolution reaction (OER) with an E-OER of 1.59 V versus RHE, surpassing the commercial IrO2 (E-OER = 1.72 V). This systematic and benchmarking study provides a basis for the future design of advanced multi-functional electrocatalysts by modulating and combining the metallic nature of nanoclusters and single atoms.
ADVANCED FUNCTIONAL MATERIALS
(2023)
Article
Energy & Fuels
Inaki Adanez-Rubio, Tobias Mattisson, Marijke Jacobs, Juan Adanez
Summary: Chemical Looping with Oxygen Uncoupling (CLOU) is a technology that separates the oxygen for fuel combustion using an oxygen carrier in a fuel reactor. This study investigates the behavior of Mn/Mg/Si system as oxygen carriers for CLOU. The most reactive oxygen carriers without Si in the structure were found to be M24Mg76 and M48Mg51. These carriers showed good reactivity and mechanical stability in a batch fluidized bed reactor.
Article
Chemistry, Applied
Amirhossein Filsouf, Inaki Adanez-Rubio, Teresa Mendiara, Alberto Abad, Juan Adanez
Summary: Chemical looping with oxygen uncoupling (CLOU) process utilizes two interconnected fluidized bed reactors, where Cu-based oxygen carriers containing a kaolin-reinforced MnFe mixed oxide as a magnetic support were prepared to improve their properties. The effects of kaolin concentration and calcination temperature on the carriers' magnetic permeability, crushing strength, attrition, agglomeration resistance, and reactivity were studied. Two oxygen carriers containing 28.5 wt% CuO-5 wt% kaolin and 30 wt% CuO-7.5 wt% kaolin, respectively, both calcined at 1100 degrees C, showed improved mechanical resistance and maintained their magnetic properties and reactivity.
FUEL PROCESSING TECHNOLOGY
(2023)
Article
Chemistry, Physical
Sergio Garcia-Dali, Javier Quilez-Bermejo, Raj Karthik, Rafael Luan Sehn Canevesi, Maria T. Izquierdo, Melanie Emo, Alain Celzard, Vanessa Fierro
Summary: The sluggish kinetics of the oxygen evolution reaction (OER) is a major limitation for green electrochemical devices. Expensive ruthenium and iridium oxide electrodes have been used as advanced electrocatalysts, but their rarity limits their global implementation. Transition metal and boron compounds show promise as alternatives due to their high catalytic properties and stability. However, their synthesis routes often involve expensive supports, increasing the cost. This study presents an easy and support-free synthesis of bimetallic borates, showing improved electrocatalytic properties for OER, particularly with nickel as the transition metal. A support-free synthesis route achieved an overpotential of 230 mV, comparable to commercial and state-of-the-art electrocatalysts.
ACS APPLIED ENERGY MATERIALS
(2023)
Article
Chemistry, Physical
Sergio Garcia-Dali, Javier Quilez-Bermejo, Jimena Castro-Gutierrez, Niki Baccile, Maria T. Izquierdo, Alain Celzard, Vanessa Fierro
Summary: This study presents efficient electrodes for the hydrogen evolution reaction (HER) based on low-cost and metal-free carbon catalysts. Phytic acid, a biosourced molecule containing carbon (C) and phosphorus (P), is used as a precursor to produce P-doped carbon materials. The conversion of P-O-type groups into P-C-type species is crucial for the catalytic activity of P-doped carbon materials, with P-C-type groups being the key factor in the electrocatalytic activity.
Article
Energy & Fuels
Arturo Cabello, Teresa Mendiara, M. Teresa Izquierdo, Francisco Garcia-Labiano, Alberto Abad
Summary: This study investigated the use of a low-cost Fe-based residue as an oxygen carrier in the Chemical Looping Combustion (CLC) and Chemical Looping Reforming (CLR) processes with biogas. The results showed that the methane combustion efficiency in the CLC process was higher (around 86%) compared to other low-cost Fe-based materials. The dry reforming of biogas in the CLR process achieved about 55% methane conversion and a yield of 1.3 mol (CO + H2)/mol CH4 for syngas production.
Article
Energy & Fuels
Margarita de las Obras Loscertales, Alberto Abad, Francisco Garcia-Labiano, Juan A. C. Ruiz, Juan Adanez
Summary: The use of bio-ethanol in chemical looping combustion and reforming has the potential to produce energy and/or hydrogen, as well as remove CO2 from the atmosphere. This study examines the kinetics of ethanol conversion using a NiO-based material as the oxygen carrier. Experiment results suggest that ethanol decomposition products, rather than direct reduction with ethanol, are responsible for NiO reduction. The high temperature kinetics of ethanol conversion processes were determined, and a reaction pathway was proposed for detailed fuel reactor models.
Article
Energy & Fuels
Oscar Condori, Alberto Abad, Maria T. Izquierdo, Luis F. de Diego, Francisco Garcia-Labiano, Juan Adanez
Summary: In this study, the Biomass Chemical Looping Gasification (BCLG) process was evaluated using wheat straw pellets and ilmenite as the fuel feedstock and oxygen carrier respectively. The effect of different operational variables on process performance and syngas yield was analyzed, and no agglomeration issues were observed during the smooth operation of the CLG unit. The oxygen transference rate in the fuel reactor was found to be the main factor affecting syngas yield and cold gas efficiency.
Article
Engineering, Chemical
Inaki Adanez-Rubio, Amirhossein Filsouf, Merve Durmaz, Teresa Mendiara, Pilar Gayan, Juan Adanez
Summary: This study focuses on testing a Cu-based oxygen carrier with enhanced mechanical properties due to the addition of kaolin in the combustion of different biomass types in a continuous CLOU unit. Complete combustion of the biomass types was achieved and higher CO2 capture efficiencies were observed at 800-950 degrees C compared to without kaolin doping. The oxygen carrier retained its magnetic properties without any agglomeration problems after 80 hours of hot circulation operation.
Correction
Chemistry, Applied
Jia Liu, Juntong Dong, Xiaodan Li, Teng Xu, Zhenguo Li, Jeffrey Dankwa Ampah, Mubasher Ikram, Shihai Zhang, Chao Jin, Zhenlong Geng, Tianyun Sun, Haifeng Liu
FUEL PROCESSING TECHNOLOGY
(2024)
Article
Chemistry, Applied
Seba Alareeqi, Daniel Bahamon, Kyriaki Polychronopoulou, Lourdes F. Vega
Summary: This study explores the potential application of single-atom-alloy (SAA) catalysts in bio-oils hydrodeoxygenation refining using density functional theory (DFT) and microkinetic modeling. It establishes the relationships between stability, adsorptive properties, and activity structures for bio-oil derivatives, providing guidance for the synthesis of cost-effective SAA combinations.
FUEL PROCESSING TECHNOLOGY
(2024)
Article
Chemistry, Applied
Bin Hu, Wen -Ming Zhang, Xue-Wen Guo, Ji Liu, Xiao Yang, Qiang Lu
Summary: This study explored the pyrolysis behaviors and mechanisms of different monosaccharides, including arabinose, galactose, galacturonic acid, and glucuronic acid. The roles of structural differences in these monosaccharides were analyzed, and it was found that glucuronic acid undergoes a special C-C bond breaking reaction during pyrolysis. The findings provide a deep understanding of the pyrolysis chemistry of hemicellulose and the role of different branches.
FUEL PROCESSING TECHNOLOGY
(2024)
Review
Chemistry, Applied
Youwei Zhi, Donghai Xu, Guanyu Jiang, Wanpeng Yang, Zhilin Chen, Peigao Duan, Jie Zhang
Summary: Hydrothermal carbonization (HTC) is an effective method for the harmless disposal of municipal sludge (MS) and offers potential applications for the obtained products. Optimizing reaction conditions, coupling with other waste materials, and combining different processes can improve the performance of HTC. Furthermore, HTC contributes to energy recovery and enhances the quality of life cycle assessment.
FUEL PROCESSING TECHNOLOGY
(2024)
Article
Chemistry, Applied
Jia Wang, Jianchun Jiang, Dongxian Li, Xianzhi Meng, Arthur J. Ragauskas
Summary: This study presents a scalable process for converting holocellulose and cellulosic wastes into advanced oxygen-containing biofuels with high furan, cyclic ketone, and ethanol content. By combining hydropyrolysis and vapor-phase hydrodeoxygenation using Pd/Al2O3 as a catalyst, the researchers achieved high yields and conversions. The integrated process holds great promise for biomass waste conversion into advanced biofuels.
FUEL PROCESSING TECHNOLOGY
(2024)
Article
Chemistry, Applied
Florian Held, Jannis Reusch, Steffen Salenbauch, Christian Hasse
Summary: The accurate prediction and assessment of soot emissions in internal combustion engines are crucial for the development of sustainable powertrains. This study presents a detailed quadrature-based method of moments (QMOM) soot model coupled with a state-of-the-art flow solver for the simulation of gasoline engines. The model accurately describes the entire cause-and-effect chain of soot formation, growth and oxidation. Experimental validation and engine cycle simulations are used to identify the root cause of observed soot formation hotspots.
FUEL PROCESSING TECHNOLOGY
(2024)