标题
Neural Network Modelling of Track Profile in Cold Spray Additive Manufacturing
作者
关键词
-
出版物
Materials
Volume 12, Issue 17, Pages 2827
出版商
MDPI AG
发表日期
2019-09-03
DOI
10.3390/ma12172827
参考文献
相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。- Strategies to develop robust neural network models: Prediction of flash point as a case study
- (2018) Amin Alibakshi ANALYTICA CHIMICA ACTA
- Solid-state additive manufacturing and repairing by cold spraying: A review
- (2018) Wenya Li et al. JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY
- Pin Fin Array Heat Sinks by Cold Spray Additive Manufacturing: Economics of Powder Recycling
- (2018) J. Perry et al. JOURNAL OF THERMAL SPRAY TECHNOLOGY
- Optimization strategies for robotic additive and subtractive manufacturing of large and high thin-walled aluminum structures
- (2018) Guocai Ma et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Modeling of Thickness and Profile Uniformity of Thermally Sprayed Coatings Deposited on Cylinders
- (2017) Zhang Yanjun et al. JOURNAL OF THERMAL SPRAY TECHNOLOGY
- Modelling of coating thickness distribution and its application in offline programming software
- (2017) C. Chen et al. SURFACE & COATINGS TECHNOLOGY
- Influence of a shape of single track on deposition efficiency of 316L stainless steel powder in cold spray
- (2017) D. Kotoban et al. SURFACE & COATINGS TECHNOLOGY
- Development of Sustainable Cold Spray Coatings and 3D Additive Manufacturing Components for Repair/Manufacturing Applications: A Critical Review
- (2017) Sunil Pathak et al. Coatings
- Effect of spray conditions on deposition behavior and microstructure of cold sprayed Ni coatings sprayed with a porous electrolytic Ni powder
- (2016) Xiao-Tao Luo et al. SURFACE & COATINGS TECHNOLOGY
- A versatile model for the prediction of complex geometry in 3D direct laser deposition
- (2016) O. Nenadl et al. SURFACE & COATINGS TECHNOLOGY
- Cold sprayed refractory metals for chrome reduction in gun barrel liners
- (2015) Blake Barnett et al. INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS
- Pyramidal Fin Arrays Performance Using Streamwise Anisotropic Materials by Cold Spray Additive Manufacturing
- (2015) Yannick Cormier et al. JOURNAL OF THERMAL SPRAY TECHNOLOGY
- A multi-bead overlapping model for robotic wire and arc additive manufacturing (WAAM)
- (2015) Donghong Ding et al. ROBOTICS AND COMPUTER-INTEGRATED MANUFACTURING
- Metal Additive Manufacturing: A Review
- (2014) William E. Frazier JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE
- High velocity impact induced microstructure evolution during deposition of cold spray coatings: A review
- (2014) Xiao-Tao Luo et al. SURFACE & COATINGS TECHNOLOGY
- Residual stress development in cold sprayed Al, Cu and Ti coatings
- (2013) T. Suhonen et al. ACTA MATERIALIA
- Dimensional accuracy improvement of FDM square cross-section parts using artificial neural networks and an optimization algorithm
- (2013) A. Noriega et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Potential of cold gas dynamic spray as additive manufacturing technology
- (2013) A. Sova et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- The Effect of Spray Distance and Scanning Step on the Coating Thickness Uniformity in Cold Spray Process
- (2013) Zhenhua Cai et al. JOURNAL OF THERMAL SPRAY TECHNOLOGY
- Simulation and parameter optimization of flux cored arc welding using artificial neural network and particle swarm optimization algorithm
- (2012) D. Katherasan et al. JOURNAL OF INTELLIGENT MANUFACTURING
- Bead geometry prediction for robotic GMAW-based rapid manufacturing through a neural network and a second-order regression analysis
- (2012) Jun Xiong et al. JOURNAL OF INTELLIGENT MANUFACTURING
- Fatigue behavior of annealed cold-sprayed 316L stainless steel coating for biomedical applications
- (2012) B. AL-Mangour et al. MATERIALS LETTERS
- Mechanical properties of Inconel 625 cold-sprayed coatings after laser remelting. Depth sensing indentation analysis
- (2012) P. Poza et al. SURFACE & COATINGS TECHNOLOGY
- Weld bead modeling and process optimization in Hybrid Layered Manufacturing
- (2011) S. Suryakumar et al. COMPUTER-AIDED DESIGN
- Prediction of pulsed-laser powder deposits’ shape profiles using a back-propagation artificial neural network
- (2008) M M Mahapatra et al. PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE
- Standoff distance and bow shock phenomena in the Cold Spray process
- (2007) J. Pattison et al. SURFACE & COATINGS TECHNOLOGY
Find the ideal target journal for your manuscript
Explore over 38,000 international journals covering a vast array of academic fields.
SearchAsk a Question. Answer a Question.
Quickly pose questions to the entire community. Debate answers and get clarity on the most important issues facing researchers.
Get Started