Effect of Holding Temperature on Microstructure and Mechanical Properties of High-Strength Multiphase Steel

Alloying effects on microstructure formation of dual phase steels

(2015) L. Schemmann et al.   ACTA MATERIALIA

A model for the microstructure behaviour and strength evolution in lath martensite

(2015) E.I. Galindo-Nava et al.   ACTA MATERIALIA

An Overview of Dual-Phase Steels: Advances in Microstructure-Oriented Processing and Micromechanically Guided Design

(2015) C.C. Tasan et al.   Annual Review of Materials Research

Effect of holding time on the microstructure and mechanical properties of dual-phase steel during intercritical annealing

(2015) Zhuang Li et al.   JOURNAL OF WUHAN UNIVERSITY OF TECHNOLOGY-MATERIALS SCIENCE EDITION

Influence of Intra-granular Ferrite on the Tensile Behavior of Intercritically Annealed 12 pct Mn TWIP+TRIP Steel

(2015) Sangwon Lee et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Integrated experimental–simulation analysis of stress and strain partitioning in multiphase alloys

(2014) C.C. Tasan et al.   ACTA MATERIALIA

Microstructure development and mechanical properties of quenching and partitioning (Q&P) steel and an incorporation of hot-dipping galvanization during Q&P process

(2013) Jing Sun et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Thermodynamically Based Prediction of the Martensite Start Temperature for Commercial Steels

(2012) Albin Stormvinter et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Acceleration of spheroidization in eutectoid steels by the addition of aluminum

(2012) H.L. Yi et al.   SCRIPTA MATERIALIA

Microstructural development during the quenching and partitioning process in a newly designed low-carbon steel

(2011) M.J. Santofimia et al.   ACTA MATERIALIA

Experimental and numerical study on geometrically necessary dislocations and non-homogeneous mechanical properties of the ferrite phase in dual phase steels

(2011) J. Kadkhodapour et al.   ACTA MATERIALIA

Effects of Si on Microstructural Evolution and Mechanical Properties of Hot-rolled Ferrite and Bainite Dual-phase Steels

(2011) Ming-hui Cai et al.   ISIJ INTERNATIONAL

Effect of Hot Working on Secondary Phase Formation in 2205 Duplex Stainless Steel

(2011) A. Momeni et al.   JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY

A new effect of retained austenite on ductility enhancement in high-strength quenching–partitioning–tempering martensitic steel

(2011) Ke Zhang et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Influence of temperature field on the microstructure of low carbon microalloyed ferrite–bainite dual-phase steel during heat treatment

(2011) Shaopeng Qu et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Effect of Heating Rate on the Austenite Formation in Low-Carbon High-Strength Steels Annealed in the Intercritical Region

(2011) R. R. Mohanty et al.   METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE

Deformation and fracture mechanisms in fine- and ultrafine-grained ferrite/martensite dual-phase steels and the effect of aging

(2010) Marion Calcagnotto et al.   ACTA MATERIALIA

Effect of niobium and rolling parameters on the mechanical properties and microstructure of dual phase steels

(2010) H. Niakan et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

Effect of cooling rate on the high strain rate properties of boron steel

(2009) Alexander Bardelcik et al.   INTERNATIONAL JOURNAL OF IMPACT ENGINEERING

Comparison of mechanical properties of martensite/ferrite and bainite/ferrite dual phase 4340 steels

(2009) N. Saeidi et al.   MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING

An investigation of mechanical and metallurgical properties of explosive welded aluminum–dual phase steel

(2008) Mustafa Acarer et al.   MATERIALS LETTERS

Carbon partitioning to austenite from martensite or bainite during the quench and partition (Q&P) process: A critical assessment

(2007) A.J. Clarke et al.   ACTA MATERIALIA