Effect of tool nose radius and tool wear on residual stresses distribution while turning in situ TiB2/7050 Al metal matrix composites
出版年份 2018 全文链接
标题
Effect of tool nose radius and tool wear on residual stresses distribution while turning in situ TiB2/7050 Al metal matrix composites
作者
关键词
-
出版物
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
Volume -, Issue -, Pages -
出版商
Springer Nature America, Inc
发表日期
2018-09-22
DOI
10.1007/s00170-018-2742-y
参考文献
相关参考文献
注意:仅列出部分参考文献,下载原文获取全部文献信息。- Investigation of cutting forces, surface integrity, and tool wear when high-speed milling of high-volume fraction SiCp/Al6063 composites in PCD tooling
- (2018) Junfeng Xiang et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Contribution of machining to the fatigue behaviour of metal matrix composites (MMCs) of varying reinforcement size
- (2017) A. Pramanik et al. INTERNATIONAL JOURNAL OF FATIGUE
- Microstructural and mechanical anisotropy of extruded in-situ TiB 2 /2024 composite plate
- (2017) Jiwei Geng et al. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING
- Microstructural correlated damage mechanisms of the high-cycle fatigued in-situ TiB 2 /Al-Cu-Mg composite
- (2017) Jiwei Geng et al. MATERIALS & DESIGN
- Formation of surface layer in metal matrix composite A359/20SiCP during laser assisted turning
- (2016) D. Przestacki et al. COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING
- Tool wear mechanisms for milling in situ TiB2 particle-reinforced Al matrix composites
- (2016) Yifeng Xiong et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- State-of-the-art in surface integrity in machining of nickel-based super alloys
- (2016) A. Thakur et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- The solution treatment of in-situ sub-micron TiB2/2024 Al composite
- (2016) Jiwei Geng et al. MATERIALS & DESIGN
- Turning of aluminum metal matrix composites: influence of the reinforcement and the cutting condition on the surface layer of the workpiece
- (2016) Jan C. Aurich et al. Advances in Manufacturing
- Effect of the cutting condition and the reinforcement phase on the thermal load of the workpiece when dry turning aluminum metal matrix composites
- (2015) Jan C. Aurich et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- An experimental study on milling of high-volume fraction SiCP/Al composites with PCD tools of different grain size
- (2015) Yinfei Yang et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- The effect of tool nose radius on surface integrity and residual stresses when turning Inconel 718™
- (2015) A.R.C. Sharman et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Quantitative study of particle size distribution in an in-situ grown Al–TiB2 composite by synchrotron X-ray diffraction and electron microscopy
- (2015) Y. Tang et al. MATERIALS CHARACTERIZATION
- Analysis of residual stress and work-hardened profiles on Inconel 718 when face turning with large-nose radius tools
- (2014) A. Madariaga et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Precision milling of high volume fraction SiCp/Al composites with monocrystalline diamond end mill
- (2013) R. Bian et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Effect of cutting parameters in the surface residual stresses generated by turning in AISI 4340 steel
- (2012) Virginia García Navas et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- Modeling of machining of composite materials: A review
- (2012) Chinmaya R. Dandekar et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- Influencing the residual stresses in the surface layer by use of appropriate cutting parameters and tool geometries in turning of aluminium matrix composites
- (2012) A. Schubert et al. MATERIALWISSENSCHAFT UND WERKSTOFFTECHNIK
- Experimental study of high-speed milling of SiCp/Al composites with PCD tools
- (2011) S. T. Huang et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Investigations of flank wear, cutting force, and surface roughness in the machining of Al-6061–TiB2 in situ metal matrix composites produced by flux-assisted synthesis
- (2010) V. Anandakrishnan et al. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY
- Residual stresses in face finish turning of high strength nickel-based superalloy
- (2009) W. Li et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Machining of metal matrix composites: Effect of ceramic particles on residual stress, surface roughness and chip formation
- (2008) A. Pramanik et al. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE
- The influence of tool flank wear on residual stresses induced by milling aluminum alloy
- (2008) Z.T. Tang et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Experimental study of surface integrity during end milling of Al/SiC particulate metal–matrix composites
- (2007) N. Suresh Kumar Reddy et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
- Investigation of mechanical and machinability properties of SiC particle reinforced Al-MMC
- (2007) Tamer Ozben et al. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY
Find the ideal target journal for your manuscript
Explore over 38,000 international journals covering a vast array of academic fields.
SearchBecome a Peeref-certified reviewer
The Peeref Institute provides free reviewer training that teaches the core competencies of the academic peer review process.
Get Started